{"title":"Eibach Pro-Kit Lowering Springs","description":"\u003cp\u003ePro-Kit is Eibach's everyday lowering spring. It lowers the car and sharpens the stance while keeping the original dampers and mounts, so the car stays comfortable enough to drive every day. Exact drop depends on the vehicle — across the kits we stock it runs 15–45 mm at the front and 5–40 mm at the rear.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"\/collections\/eibach\"\u003eAll Eibach\u003c\/a\u003e · \u003ca href=\"\/pages\/vehicles\"\u003eBrowse by vehicle\u003c\/a\u003e · \u003ca href=\"\/pages\/parts-a-z\"\u003eParts A–Z\u003c\/a\u003e\u003c\/p\u003e","products":[{"product_id":"e10-15-009-01-22","title":"Eibach Pro-Kit Lowering Springs E10-15-009-01-22 – Audi TT (8J3)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-15-009-01-22 for the Audi TT (8J3), lowering the car by 25 mm at the front and 20 mm at the rear, approved to 1005 kg front and 800 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-15-009-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1005 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 800 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-009-01-VA, 2 × rear axle spring F11-15-009-01-HA, M45-85-014-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1015009.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm at the front and 20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Audi TT (8J3), 08\/2006–06\/2014, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-audi\"\u003eAudi\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-009-01-VA · 2 × rear axle spring F11-15-009-01-HA · M45-85-014-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57407277531460,"sku":"E10-15-009-01-22","price":203.23,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-11-001-01-22","title":"Eibach Pro-Kit Lowering Springs E10-11-001-01-22 – Cupra Born \/ VW ID.3","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-11-001-01-22 for the Cupra Born (K11), lowering the car by 20–25 mm, approved to 1120 kg front and 1270 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-11-001-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20–25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20–25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e77, 77 e-boost, 82, 84:\u003c\/strong\u003e 20 mm front \/ 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eID.3 Pro S:\u003c\/strong\u003e 25 mm front \/ 25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1120 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1270 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-85-043-01-FA, F11-85-052-02-RA, M45-85-052-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1085052.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1085052.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20–25 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Cupra Born (K11), from 08\/2021, RWD; and Volkswagen ID.3 (E11, E12), from 11\/2021 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-85-043-01-FA · F11-85-052-02-RA · M45-85-052-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57407277760836,"sku":"E10-11-001-01-22","price":244.76,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-20-031-04-22","title":"Eibach Pro-Kit Lowering Springs E10-20-031-04-22 – BMW 3 Series, 4 Series","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-20-031-04-22 for the BMW 3 (F30, F80), lowering the car by 20–40 mm at the front and 15–30 mm at the rear, approved to 1010 kg front and 1310 kg rear axle load, covering 4 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-20-031-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20–40 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 15–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e330 e:\u003c\/strong\u003e 30 mm front \/ 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e320 i xDrive, 328 i xDrive, 330 i xDrive, 320 d xDrive:\u003c\/strong\u003e 20 mm front \/ 15 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e335 i, 340 i, 325 d, 330 d:\u003c\/strong\u003e 25–30 mm front \/ 25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e320 i, 330 i, 335 i, 340 i, 320 i x-Drive, 320 d x-Drive, 320 d, 325 d, 330 d:\u003c\/strong\u003e 30–40 mm front \/ 25–30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e420 i xDrive, 428 i xDrive, 430 i xDrive, 420 d xDrive:\u003c\/strong\u003e 25 mm front \/ 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e up to 1020 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1310 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-20-031-02-VA, 2 × rear axle spring F11-20-031-03-HA, M45-20-045-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e ABE1020031.pdf, E1020031.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 4 vehicles, 5 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20–40 mm at the front and 15–30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW 3 (F30, F80), 11\/2015–10\/2018, RWD; BMW 3 (F30, F80), 10\/2011–10\/2018, AWD; BMW 3 Touring (F31), 06\/2012–06\/2019, RWD; BMW 3 Gran Tourismo (F34), from 03\/2013, RWD; and BMW 4 Gran Coupe (F36), from 03\/2014, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw-3-series\"\u003eBMW 3 Series\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-20-031-02-VA · 2 × rear axle spring F11-20-031-03-HA · M45-20-045-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eSpacer plates M45-20-045-01-01 included in the scope of delivery are optionally provided for the use of BMW 3 Touring (F31) with a high curb weight (e.g. vehicles with glass roof).\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57407277793604,"sku":"E10-20-031-04-22","price":213.3,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-79-010-02-22","title":"Eibach Pro-Kit Lowering Springs E10-79-010-02-22 – Škoda Octavia \/ VW Golf \/ Seat Leon","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-79-010-02-22 for the Skoda Octavia III (5E3, NL3, NR3), lowering the car by 15–40 mm at the front and 10–30 mm at the rear, approved to 1075 kg front and 1150 kg rear axle load, covering 7 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-79-010-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 15–40 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 10–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.8 TSI, 2.0 TSI, 1.6 TDI, 2.0 TDI:\u003c\/strong\u003e 35 mm front \/ 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 Cupra:\u003c\/strong\u003e 15 mm front \/ 10 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.8 TSI, 2.0 TSI, 1.6 TDI, 2.0 TDI, 1.8 TSI 4x4, 2.0 TSI 4x4, 1.6 TDI 4x4, 2.0 TDI 4x4…:\u003c\/strong\u003e 30–40 mm front \/ 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 TSI RS, 2.0 TDI RS:\u003c\/strong\u003e 20 mm front \/ 10 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 TDI RS 4x4:\u003c\/strong\u003e 30 mm front \/ 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.8 TSI, 1.6 TDI, 2.0 TDI, 2.0 TSI:\u003c\/strong\u003e 30 mm front \/ 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 GTD:\u003c\/strong\u003e 15 mm front \/ 15 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e up to 1090 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e up to 1150 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-021-02-VA, 2 × rear axle spring F11-15-007-15-HA, M45-85-014-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eAdditional component part numbers:\u003c\/strong\u003e 2 × front damper AZ45-85-043-01-03\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e ABE15021.pdf, ABE1015021.pdf, E1015021.pdf, E1085051.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e ABEM15021.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 7 vehicles, 14 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 15–40 mm at the front and 10–30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Seat Leon ST (5F8), from 10\/2013, AWD; Seat Leon ST Van\/Estate (5F8), from 10\/2013, AWD; Seat Leon ST Van\/Estate (5F8), from 10\/2013; Skoda Octavia III (5E3, NL3, NR3), 11\/2012–10\/2020, AWD; Skoda Octavia III (5E3, NL3, NR3), 11\/2012–10\/2020, FWD; Skoda Octavia III (5E3, NL3, NR3), 09\/2014–10\/2020, AWD; Skoda Octavia III Combi \/ Station Wagon (5E5), 11\/2012–10\/2020, AWD; Skoda Octavia III Combi \/ Station Wagon (5E5), 11\/2012–10\/2020, FWD; Skoda Octavia III Combi \/ Station Wagon (5E5), 09\/2014–10\/2020, AWD; Volkswagen Golf VII Variant (BA5, BV5), from 04\/2013, FWD; Volkswagen Golf VII Variant (BA5, BV5), from 01\/2015, FWD; Volkswagen Golf Sportsvan (AM1, AN1), from 02\/2014, FWD; and Volkswagen Golf VIII Variant (CG5), from 08\/2020, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-skoda-octavia\"\u003eŠkoda Octavia\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-021-02-VA · 2 × rear axle spring F11-15-007-15-HA · M45-85-014-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003eThe original Volkswagen rubber plate 5Q0 512 149 G (9mm) or 8J0 512 149 (13 mm) can be used optionally for vehicles with heavy equipment variants (e.g. rear wheel, trailer coupling, glas roof, etc.) - detailed information can be found in the parts certificate. This is an optinally exchange for the standard VW rubber plate 5Q0 512 149 F (6mm). Only available from Volkswagen dealers or original parts dealers.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57407277826372,"sku":"E10-79-010-02-22","price":169.25,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-60-013-02-22","title":"Eibach Pro-Kit Lowering Springs E10-60-013-02-22 – Mitsubishi Lancer (CY, Z\/A)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-60-013-02-22 for the Mitsubishi Lancer Saloon \/ Saloon (CY\/Z_A), lowering the car by 30 mm at the front and 25 mm at the rear, approved to 1080 kg front and 980 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-60-013-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1080 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 980 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-60-013-02-VA, 2 × rear axle spring F11-60-013-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mitsubishi Lancer Saloon \/ Saloon (CY\/Z_A), from 03\/2007 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mitsubishi-lancer\"\u003eMitsubishi Lancer\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-60-013-02-VA · 2 × rear axle spring F11-60-013-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411431858500,"sku":"E10-60-013-02-22","price":198.83,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-20-017-04-20","title":"Eibach Pro-Kit Lowering Springs E10-20-017-04-20 – BMW X6 (E71, E72)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-20-017-04-20 for the BMW X6 (E71, E72), lowering the car by 20 mm at the front and 15–20 mm at the rear, approved to 1400 kg front and 1520 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-20-017-04-20\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 15–20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1400 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1520 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-20-017-03-VA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e air-spring adjustment\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020017.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20 mm at the front and 15–20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW X6 (E71, E72), 05\/2008–07\/2014, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw\"\u003eBMW\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-20-017-03-VA (the Eibach spring column also lists: air-spring adjustment)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411431989572,"sku":"E10-20-017-04-20","price":181.84,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-15-011-03-22","title":"Eibach Pro-Kit Lowering Springs E10-15-011-03-22 – Audi A4 (8K5, B8)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-15-011-03-22 for the Audi A4 Avant (8K5, B8), lowering the car by 30 mm, approved to 1135 kg front and 1255 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-15-011-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1135 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1255 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-011-01-VA, 2 × rear axle spring F11-15-011-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e ABE1015011.pdf, E1015011.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Audi A4 Avant (8K5, B8), 04\/2008–12\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-audi-a4\"\u003eAudi A4\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-011-01-VA · 2 × rear axle spring F11-15-011-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eFor vehicles, not lowered by manufacturer. (OE-sport suspension)\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432153412,"sku":"E10-15-011-03-22","price":209.52,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-42-056-02-22","title":"Eibach Pro-Kit Lowering Springs E10-42-056-02-22 – Hyundai Bayon (BC3)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-42-056-02-22 for the Hyundai Bayon (BC3), lowering the car by 30 mm at the front and 25 mm at the rear, approved to 900 kg front and 870 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-42-056-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 900 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 870 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-42-056-02-FA, F11-42-056-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1042052.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Bayon (BC3), from 05\/2021, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-42-056-02-FA · F11-42-056-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eFor cars with rear live axle.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432218948,"sku":"E10-42-056-02-22","price":209.52,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-35-021-04-22","title":"Eibach Pro-Kit Lowering Springs E10-35-021-04-22 – Ford Kuga (DM2)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-35-021-04-22 for the Ford Kuga II \/ Escape (DM2), lowering the car by 30 mm at the front and 30–40 mm at the rear, approved to 1125 kg front and 1150 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-35-021-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30–40 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.5 Ecoboost, 1.5 Ecoboost 4x4, 1.5 TDCi:\u003c\/strong\u003e 30 mm front \/ 30–40 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.5 Ecoboost, 1.5 Ecoboost 4x4:\u003c\/strong\u003e 30 mm front \/ 40 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1125 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1150 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-35-021-04-FA, F11-35-021-04-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1035021.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 30–40 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Kuga II \/ Escape (DM2), from 09\/2014, AWD; and Ford Kuga II VAN, from 09\/2014, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-35-021-04-FA · F11-35-021-04-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432350020,"sku":"E10-35-021-04-22","price":217.07,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e1020-140","title":"Eibach Pro-Kit Lowering Springs E1020-140 – Alfa Romeo 156 (932)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E1020-140 for the Alfa Romeo 156 (932), lowering the car by 30 mm, approved to 1060 kg front and 1000 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E1020-140\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1000 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F1020001, F1020002\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020-140.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Alfa Romeo 156 (932), 09\/1997–09\/2005, FWD; and Alfa Romeo 156 Sportwagon (932), 05\/2000–05\/2006, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F1020001 · F1020002). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432415556,"sku":"E1020-140","price":209.52,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e2837-540","title":"Eibach Pro-Kit Lowering Springs E2837-540 – Jeep Grand Cherokee II (WJ, WG)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E2837-540 for the Jeep Grand Cherokee II (WJ, WG), lowering the car by 30 mm, approved to 1250 kg front and 1340 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E2837-540\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1250 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1340 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F28375001, F28375002\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E2837-540.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Jeep Grand Cherokee II (WJ, WG), 10\/1998–09\/2005, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F28375001 · F28375002). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432612164,"sku":"E2837-540","price":263.63,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-79-011-02-22","title":"Eibach Pro-Kit Lowering Springs E10-79-011-02-22 – Škoda Fabia III (NJ5)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-79-011-02-22 for the Skoda Fabia III Estate \/ Station Wagon (NJ5, NJ5), lowering the car by 30 mm at the front and 35 mm at the rear, approved to 960 kg front and 840 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-79-011-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 35 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 960 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 840 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-81-010-05-VA, 2 × rear axle spring F11-85-008-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1081010.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1085024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 35 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Skoda Fabia III Estate \/ Station Wagon (NJ5, NJ5), from 10\/2014, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-skoda-fabia\"\u003eŠkoda Fabia\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-81-010-05-VA · 2 × rear axle spring F11-85-008-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432481092,"sku":"E10-79-011-02-22","price":175.55,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-70-016-02-22","title":"Eibach Pro-Kit Lowering Springs E10-70-016-02-22 – Peugeot 508 SW I (8E_)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-70-016-02-22 for the Peugeot 508 SW I (8E_), lowering the car by 25 mm, approved to 1250 kg front and 1130 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-70-016-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1250 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1130 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-70-016-02-VA, 2 × rear axle spring F11-70-016-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1070016.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Peugeot 508 SW I (8E_), 11\/2010–12\/2018 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-70-016-02-VA · 2 × rear axle spring F11-70-016-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eOnly for suspension strut at the front axle (McPherson)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432513860,"sku":"E10-70-016-02-22","price":237.21,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-25-001-06-22","title":"Eibach Pro-Kit Lowering Springs E10-25-001-06-22 – Mercedes-Benz C-Class Estate (S203)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-25-001-06-22 for the Mercedes-Benz C-Class Estate (S203), lowering the car by 30 mm, approved to 1090 kg front and 1170 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-25-001-06-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1090 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1170 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-25-001-01-VA, 2 × rear axle spring F11-25-001-05-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E102500105.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mercedes-Benz C-Class Estate (S203), 03\/2001–08\/2007 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mercedes-benz-c-class\"\u003eMercedes-Benz C-Class\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-25-001-01-VA · 2 × rear axle spring F11-25-001-05-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eThe spring plates installed by the manufacturer are available at DB specialist workshops in sizes 8-23 mm. This allows to vary the lowering indicated here.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003efor vehicles without AMG-suspension\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432710468,"sku":"E10-25-001-06-22","price":189.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-84-022-03-22","title":"Eibach Pro-Kit Lowering Springs E10-84-022-03-22 – Volvo EX30 (416)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-84-022-03-22 for the Lynk \u0026amp; Co 02 | Z20, lowering the car by 30–45 mm at the front and 25–40 mm at the rear, approved to 1100 kg front and 1355 kg rear axle load, covering 4 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-84-022-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30–45 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25–40 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEV 200kw:\u003c\/strong\u003e 45 mm front \/ 40 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEV RWD (200kw), Single Motor RWD (200kw):\u003c\/strong\u003e 30 mm front \/ 25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1100 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1355 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-84-022-03-FA, F11-56-004-03-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1056004.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 4 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30–45 mm at the front and 25–40 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Lynk \u0026amp; Co 02 | Z20, from 12\/2024; Smart #1 (HX11), from 08\/2022; Smart #3 (HC11), from 06\/2023; and Volvo EX30 (416), from 06\/2023, RWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-84-022-03-FA · F11-56-004-03-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003ewheel base: 2755 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411432776004,"sku":"E10-84-022-03-22","price":234.06,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-15-011-04-22","title":"Eibach Pro-Kit Lowering Springs E10-15-011-04-22 – Audi A4 (8K5, B8)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-15-011-04-22 for the Audi A4 Avant (8K5, B8), lowering the car by 20–30 mm at the front and 15–30 mm at the rear, approved to 1225 kg front and 1255 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-15-011-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 15–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 TDI quattro, 3.0 TFSI quattro, 3.2 FSI quattro mit tiptronic, 3.0 TDI quattro:\u003c\/strong\u003e 30 mm front \/ 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eS4 quattro:\u003c\/strong\u003e 20 mm front \/ 15 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1225 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1255 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-011-02-VA, 2 × rear axle spring F11-15-011-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e ABE1015011.pdf, E1015011.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20–30 mm at the front and 15–30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Audi A4 Avant (8K5, B8), 04\/2008–12\/2015, AWD; and Audi A4 Avant (8K5, B8), 11\/2008–12\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-audi-a4\"\u003eAudi A4\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-011-02-VA · 2 × rear axle spring F11-15-011-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eFor vehicles, not lowered by manufacturer. (OE-sport suspension)\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433398596,"sku":"E10-15-011-04-22","price":209.52,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-20-018-01-22","title":"Eibach Pro-Kit Lowering Springs E10-20-018-01-22 – BMW 7 Series (F01, F02, F03, F04)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-20-018-01-22 for the BMW 7 (F01, F02, F03, F04), lowering the car by 25 mm at the front and 20 mm at the rear, approved to 1235 kg front and 1500 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-20-018-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1235 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1500 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-20-018-01-VA, 2 × rear axle spring F11-20-018-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020018.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm at the front and 20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW 7 (F01, F02, F03, F04), 02\/2008–12\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw\"\u003eBMW\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-20-018-01-VA · 2 × rear axle spring F11-20-018-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433464132,"sku":"E10-20-018-01-22","price":255.46,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-79-012-01-22","title":"Eibach Pro-Kit Lowering Springs E10-79-012-01-22 – Škoda Superb III (3V3, 3V5)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-79-012-01-22 for the Skoda Superb III (3V3), lowering the car by 35 mm at the front and 30 mm at the rear, approved to 985 kg front and 1253 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-79-012-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 35 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 985 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1253 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-021-01-VA, 2 × rear axle spring F11-79-008-01-HA, M45-85-014-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e ABE1015021.pdf, E1015021.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 35 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Skoda Superb III (3V3), from 03\/2015, AWD; and Skoda Superb III Estate \/ Estate (3V5), from 03\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-021-01-VA · 2 × rear axle spring F11-79-008-01-HA · M45-85-014-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433529668,"sku":"E10-79-012-01-22","price":200.71,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-35-021-05-22","title":"Eibach Pro-Kit Lowering Springs E10-35-021-05-22 – Ford Kuga (DM2)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-35-021-05-22 for the Ford Kuga II \/ Escape (DM2), lowering the car by 30 mm at the front and 30–40 mm at the rear, approved to 1210 kg front and 1150 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-35-021-05-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30–40 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.5 Ecoboost 4x4, 2.0 4x4, 2.0 EcoBoost 4x4, 1.5 TDCi, 2.0 TDCi, 2.0 TDCi 4x4, 2.5 4x4:\u003c\/strong\u003e 30 mm front \/ 30–40 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.5 Ecoboost 4x4, 2.0 TDCi, 2.0 TDCi 4x4:\u003c\/strong\u003e 30 mm front \/ 40 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1210 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1150 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-35-021-05-FA, F11-35-021-04-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1035021.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 30–40 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Kuga II \/ Escape (DM2), from 09\/2014, AWD; and Ford Kuga II VAN, from 09\/2014, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-35-021-05-FA · F11-35-021-04-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433627972,"sku":"E10-35-021-05-22","price":217.07,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-42-061-01-22","title":"Eibach Pro-Kit Lowering Springs E10-42-061-01-22 – Hyundai IONIQ VI (CE)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-42-061-01-22 for the Hyundai Ioniq 6 (CE), lowering the car by 25–35 mm at the front and 25–30 mm at the rear, approved to 1285 kg front and 1435 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-42-061-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–35 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEV (System performance 111kw \/ Variant F5E12):\u003c\/strong\u003e 25 mm front \/ 25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEV (System performance 168kw \/ Variant F5E22):\u003c\/strong\u003e 30 mm front \/ 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eEV Allrad\/AWD (System performance 239 kw \/ Variant F5E34):\u003c\/strong\u003e 30–35 mm front \/ 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1285 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1435 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-42-061-01-FA, F11-42-055-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1042055.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 3 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25–35 mm at the front and 25–30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Ioniq 6 (CE), from 10\/2022, AWD; and Hyundai Ioniq 6 (CE), from 10\/2022 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-42-061-01-FA · F11-42-055-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433759044,"sku":"E10-42-061-01-22","price":251.05,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-60-013-03-22","title":"Eibach Pro-Kit Lowering Springs E10-60-013-03-22 – Mitsubishi Lancer (CX\/A)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-60-013-03-22 for the Mitsubishi Lancer Sportback \/ Galant Fortis (CX_A), lowering the car by 30 mm at the front and 25 mm at the rear, approved to 990 kg front and 980 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-60-013-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 990 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 980 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-60-013-01-VA, 2 × rear axle spring F11-60-013-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mitsubishi Lancer Sportback \/ Galant Fortis (CX_A), from 06\/2008, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mitsubishi-lancer\"\u003eMitsubishi Lancer\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-60-013-01-VA · 2 × rear axle spring F11-60-013-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433857348,"sku":"E10-60-013-03-22","price":198.83,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e1021-120","title":"Eibach Pro-Kit Lowering Springs E1021-120 – Alfa Romeo 156 (932)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E1021-120 for the Alfa Romeo 156 Sportwagon (932), lowering the car by 30 mm at the front.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E1021-120\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F1021001\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020-140.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Alfa Romeo 156 Sportwagon (932), 05\/2000–05\/2006, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F1021001). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433955652,"sku":"E1021-120","price":132.76,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-70-017-01-22","title":"Eibach Pro-Kit Lowering Springs E10-70-017-01-22 – Peugeot 2008 I (CU)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-70-017-01-22 for the Peugeot 2008 I (CU), lowering the car by 30 mm, approved to 1000 kg front and 900 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-70-017-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1000 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 900 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-70-009-01-VA, 2 × rear axle spring F11-22-010-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1070017.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Peugeot 2008 I (CU), from 03\/2013, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-70-009-01-VA · 2 × rear axle spring F11-22-010-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411434021188,"sku":"E10-70-017-01-22","price":180.58,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-84-024-01-22","title":"Eibach Pro-Kit Lowering Springs E10-84-024-01-22 – Volvo EX90 (356)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-84-024-01-22 for the Volvo EX90 (356), lowering the car by 35 mm at the front and 30 mm at the rear, approved to 1530 kg front and 1960 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-84-024-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 35 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1530 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1960 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-84-024-01-FA, F11-84-024-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e TTG84024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 35 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Volvo EX90 (356), from 06\/2024, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-84-024-01-FA · F11-84-024-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411434119492,"sku":"E10-84-024-01-22","price":244.13,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-25-001-08-22","title":"Eibach Pro-Kit Lowering Springs E10-25-001-08-22 – Mercedes-Benz C-Class (CL203)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-25-001-08-22 for the Mercedes-Benz C-Class Sportscoupe (CL203), lowering the car by 25–30 mm at the front and 20–25 mm at the rear, approved to 1100 kg front and 1035 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-25-001-08-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20–25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1100 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1035 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-25-001-01-VA, F2538002\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E102500104.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25–30 mm at the front and 20–25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mercedes-Benz C-Class Sportscoupe (CL203), 03\/2001–05\/2008, RWD; and Mercedes-Benz CLC-Class (CL203), 05\/2008–06\/2011 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mercedes-benz-c-class\"\u003eMercedes-Benz C-Class\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-25-001-01-VA · F2538002). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eThe spring plates installed by the manufacturer are available at DB specialist workshops in sizes 8-23 mm. This allows to vary the lowering indicated here.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003efor vehicles without AMG-suspension\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411435266372,"sku":"E10-25-001-08-22","price":189.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-79-012-02-22","title":"Eibach Pro-Kit Lowering Springs E10-79-012-02-22 – Škoda Superb III (3V3, 3V5)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-79-012-02-22 for the Skoda Superb III (3V3), lowering the car by 35 mm at the front and 30 mm at the rear, approved to 1075 kg front and 1253 kg rear axle load, covering 3 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-79-012-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 35 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1075 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1253 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-021-02-VA, 2 × rear axle spring F11-79-008-01-HA, M45-85-014-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e ABE1015021.pdf, E1015021.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 3 vehicles, 3 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 35 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Skoda Superb III (3V3), from 03\/2015, AWD; Skoda Superb III Estate \/ Estate (3V5), from 03\/2015, AWD; and Volkswagen Touran | Golf Touran (5T1), from 05\/2015 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-021-02-VA · 2 × rear axle spring F11-79-008-01-HA · M45-85-014-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411435659588,"sku":"E10-79-012-02-22","price":208.27,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-15-013-01-22","title":"Eibach Pro-Kit Lowering Springs E10-15-013-01-22 – Audi Q5 (8RB)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-15-013-01-22 for the Audi Q5 (8RB), lowering the car by 30 mm at the front and 25 mm at the rear, approved to 1255 kg front and 1360 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-15-013-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1255 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1360 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-013-01-VA, 2 × rear axle spring F11-15-013-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E10-15-013-01-22.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Audi Q5 (8RB), 11\/2008–12\/2016, AWD; and Audi Q5 VAN (8RB), 11\/2008–12\/2016, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-audi\"\u003eAudi\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-013-01-VA · 2 × rear axle spring F11-15-013-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411435495748,"sku":"E10-15-013-01-22","price":244.13,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-35-022-01-22","title":"Eibach Pro-Kit Lowering Springs E10-35-022-01-22 – Ford Ka 2 (RU8)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-35-022-01-22 for the Ford KA (RU8), lowering the car by 25 mm, approved to 770 kg front and 640 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-35-022-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 770 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 640 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-35-022-01-VA, 2 × rear axle spring F11-35-022-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1035022.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford KA (RU8), 10\/2008–05\/2016, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-35-022-01-VA · 2 × rear axle spring F11-35-022-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411435790660,"sku":"E10-35-022-01-22","price":164.85,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-20-018-02-22","title":"Eibach Pro-Kit Lowering Springs E10-20-018-02-22 – BMW 7 Series (F01, F02, F03, F04)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-20-018-02-22 for the BMW 7 (F01, F02, F03, F04), lowering the car by 25 mm at the front and 20 mm at the rear, approved to 1340 kg front and 1500 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-20-018-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1340 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1500 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-20-018-02-VA, 2 × rear axle spring F11-20-018-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020018.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm at the front and 20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW 7 (F01, F02, F03, F04), 02\/2008–12\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw\"\u003eBMW\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-20-018-02-VA · 2 × rear axle spring F11-20-018-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411435856196,"sku":"E10-20-018-02-22","price":255.46,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-70-017-02-22","title":"Eibach Pro-Kit Lowering Springs E10-70-017-02-22 – Peugeot 2008 I (CU)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-70-017-02-22 for the Peugeot 2008 I (CU), lowering the car by 30 mm, approved to 1050 kg front and 900 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-70-017-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1050 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 900 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-70-010-02-VA, 2 × rear axle spring F11-22-010-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1070017.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Peugeot 2008 I (CU), from 03\/2013, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-70-010-02-VA · 2 × rear axle spring F11-22-010-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411435954500,"sku":"E10-70-017-02-22","price":175.55,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-85-001-05-22","title":"Eibach Pro-Kit Lowering Springs E10-85-001-05-22 – VW Bora, Golf","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-85-001-05-22 for the Volkswagen Bora (1J2), lowering the car by 30 mm, approved to 1030 kg front and 1120 kg rear axle load, covering 4 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-85-001-05-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1030 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1120 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F1545001, 2 × rear axle spring F11-15-001-02-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E108500105.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M101500402.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 4 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Volkswagen Bora (1J2), 10\/1998–09\/2005, AWD; Volkswagen Bora Estate \/ Estate (1J6), 05\/1999–05\/2005; Volkswagen Golf IV (1J1), 08\/1997–06\/2005; and Volkswagen Golf IV Variant (1J5), 05\/1999–06\/2006 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-volkswagen\"\u003eVolkswagen\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F1545001 · 2 × rear axle spring F11-15-001-02-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436020036,"sku":"E10-85-001-05-22","price":185.61,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-60-013-04-22","title":"Eibach Pro-Kit Lowering Springs E10-60-013-04-22 – Mitsubishi Lancer (CX\/A)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-60-013-04-22 for the Mitsubishi Lancer Sportback \/ Galant Fortis (CX_A), lowering the car by 30 mm at the front and 25 mm at the rear, approved to 1080 kg front and 980 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-60-013-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1080 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 980 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-60-013-02-VA, 2 × rear axle spring F11-60-013-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mitsubishi Lancer Sportback \/ Galant Fortis (CX_A), from 06\/2008, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mitsubishi-lancer\"\u003eMitsubishi Lancer\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-60-013-02-VA · 2 × rear axle spring F11-60-013-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436282180,"sku":"E10-60-013-04-22","price":198.83,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e1021-140","title":"Eibach Pro-Kit Lowering Springs E1021-140 – Alfa Romeo 156 (932)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E1021-140 for the Alfa Romeo 156 (932), lowering the car by 30 mm, approved to 1060 kg front and 1000 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E1021-140\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1000 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F1021001, F1020002\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020-140.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Alfa Romeo 156 (932), 09\/1997–09\/2005, FWD; and Alfa Romeo 156 Sportwagon (932), 05\/2000–05\/2006, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F1021001 · F1020002). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436347716,"sku":"E1021-140","price":209.52,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e7003-120","title":"Eibach Pro-Kit Lowering Springs E7003-120 – Peugeot 205, 106","description":"\u003cp\u003eEibach Pro-Kit lowering springs E7003-120 for the Peugeot 106 I (1A, 1C), lowering the car by 30–40 mm at the front and 30 mm at the rear, approved to 650 kg front and 640 kg rear axle load, covering 3 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E7003-120\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30–40 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 650 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 640 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F7003001\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e torsion-bar adjustment\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E7003-120.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 3 vehicles, 3 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30–40 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Peugeot 106 I (1A, 1C), 08\/1991–04\/1996, FWD; Peugeot 205 I (741A\/C), 02\/1983–10\/1987; and Peugeot 205 I Cabriolet \/ Convertible (741B, 20D), 04\/1986–12\/1994, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F7003001 (the Eibach spring column also lists: torsion-bar adjustment)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436642628,"sku":"E7003-120","price":113.26,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-85-001-14-22","title":"Eibach Pro-Kit Lowering Springs E10-85-001-14-22 – VW Golf IV (1J1)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-85-001-14-22 for the Volkswagen Golf IV (1J1), lowering the car by 30 mm, approved to 1050 kg front and 925 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-85-001-14-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1050 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 925 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F8592001, F1540002\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E10-85-001-14-22.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Volkswagen Golf IV (1J1), 08\/1997–06\/2005 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-volkswagen-golf\"\u003eVolkswagen Golf\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F8592001 · F1540002). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eWhen the car is lowered more than 40 mm in combination with a drive shaft diameter more than 42 mm, please make sure that there is sufficient distance between the stabilizer and the drive shaft. It maybe necessary to install another anti-roll bar or other coupling rod.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436708164,"sku":"E10-85-001-14-22","price":169.25,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-35-023-01-22","title":"Eibach Pro-Kit Lowering Springs E10-35-023-01-22 – Ford Focus III","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-35-023-01-22 for the Ford Focus III, lowering the car by 25 mm, approved to 985 kg front and 1060 kg rear axle load, covering 4 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-35-023-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 985 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-35-023-01-VA, 2 × rear axle spring F11-35-014-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1035023.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 4 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Focus III, from 04\/2011; Ford Focus III Van\/Estate \/ Box\/Station Wagon, 04\/2011–08\/2014; Ford Focus III Van\/Hatchback \/ Box\/Saloon, 04\/2011–08\/2014; and Ford Focus III Saloon \/ Saloon, 04\/2011–08\/2014 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford-focus\"\u003eFord Focus\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-35-023-01-VA · 2 × rear axle spring F11-35-014-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436806468,"sku":"E10-35-023-01-22","price":189.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-20-018-03-20","title":"Eibach Pro-Kit Lowering Springs E10-20-018-03-20 – BMW 5 Series, 7 Series","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-20-018-03-20 for the BMW 5 Gran Turismo (F07), lowering the car by 25 mm at the front and 10–20 mm at the rear, approved to 1235 kg front and 1500 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-20-018-03-20\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 10–20 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e535i, 530d, 535d, 535i xDrive, 530d xDrive, 535d xDrive:\u003c\/strong\u003e 25 mm front \/ 10–15 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e730i, 740i, 740i xDrive, 730d, 740d, 730d xDrive, 740d xDrive:\u003c\/strong\u003e 25 mm front \/ 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1235 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1500 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-20-018-01-VA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e air-spring adjustment\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020018.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm at the front and 10–20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW 5 Gran Turismo (F07), 01\/2009–02\/2017, AWD; and BMW 7 (F01, F02, F03, F04), 02\/2008–12\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw-5-series\"\u003eBMW 5 Series\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-20-018-01-VA (the Eibach spring column also lists: air-spring adjustment)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436872004,"sku":"E10-20-018-03-20","price":152.27,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-15-013-02-22","title":"Eibach Pro-Kit Lowering Springs E10-15-013-02-22 – Audi Q5 (8RB)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-15-013-02-22 for the Audi Q5 (8RB), lowering the car by 15–30 mm at the front and 5–25 mm at the rear, approved to 1325 kg front and 1360 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-15-013-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 15–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 5–25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e3.0 TFSI quattro, 3.0 TDI quattro:\u003c\/strong\u003e 30 mm front \/ 25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSQ5 TFSI quattro, SQ5 TDI quattro, 3.0 SQ5 TDI quattro:\u003c\/strong\u003e 15 mm front \/ 5 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1325 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1360 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-013-02-VA, 2 × rear axle spring F11-15-013-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E10-15-013-02-22.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 15–30 mm at the front and 5–25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Audi Q5 (8RB), 11\/2008–12\/2016, AWD; Audi Q5 VAN (8RB), 11\/2008–12\/2016, AWD; and Audi Q5 VAN (8RB), 11\/2008–12\/2016 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-audi\"\u003eAudi\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-013-02-VA · 2 × rear axle spring F11-15-013-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437035844,"sku":"E10-15-013-02-22","price":244.13,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-42-062-02-22","title":"Eibach Pro-Kit Lowering Springs E10-42-062-02-22 – Hyundai Kona (SX2)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-42-062-02-22 for the Hyundai Kona (SX2), lowering the car by 30–35 mm at the front and 20–25 mm at the rear, approved to 1105 kg front and 1035 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-42-062-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30–35 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20–25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.0 T-GDI Hybrid 48V, 1.6 T-GDI 4WD:\u003c\/strong\u003e 30 mm front \/ 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 GDi Hybrid (104kw):\u003c\/strong\u003e 35 mm front \/ 25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1105 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1035 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-42-062-02-FA, F11-42-062-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1042062.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30–35 mm at the front and 20–25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Kona (SX2), from 04\/2023, AWD; and Kia Niro (SG2), from 06\/2022 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-42-062-02-FA · F11-42-062-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437101380,"sku":"E10-42-062-02-22","price":251.05,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-60-013-06-22","title":"Eibach Pro-Kit Lowering Springs E10-60-013-06-22 – Mitsubishi Lancer (CX\/A)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-60-013-06-22 for the Mitsubishi Lancer Sportback \/ Galant Fortis (CX_A), lowering the car by 30 mm at the front and 25 mm at the rear, approved to 905 kg front and 980 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-60-013-06-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 905 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 980 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-60-016-01-VA, 2 × rear axle spring F11-60-013-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mitsubishi Lancer Sportback \/ Galant Fortis (CX_A), from 06\/2008, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mitsubishi-lancer\"\u003eMitsubishi Lancer\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-60-016-01-VA · 2 × rear axle spring F11-60-013-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437199684,"sku":"E10-60-013-06-22","price":188.13,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e7005-120","title":"Eibach Pro-Kit Lowering Springs E7005-120","description":"\u003cp\u003eEibach Pro-Kit lowering springs E7005-120 for the Peugeot 309 I (10C, 10A), lowering the car by 20–30 mm at the front and 30 mm at the rear, approved to 750 kg front and 750 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E7005-120\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 750 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 750 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F7005001\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e torsion-bar adjustment\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E7005-120.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20–30 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Peugeot 309 I (10C, 10A), 10\/1985–12\/1989; and Peugeot 309 II (3C, 3A), 07\/1989–12\/1993 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F7005001 (the Eibach spring column also lists: torsion-bar adjustment)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437461828,"sku":"E7005-120","price":135.28,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-85-001-15-22","title":"Eibach Pro-Kit Lowering Springs E10-85-001-15-22 – VW Bora, Golf","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-85-001-15-22 for the Volkswagen Bora Estate \/ Estate (1J6), lowering the car by 30 mm, approved to 1050 kg front and 1020 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-85-001-15-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1050 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1020 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F8592001, F7908002\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E10-85-001-15-22.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Volkswagen Bora Estate \/ Estate (1J6), 05\/1999–05\/2005, FWD; and Volkswagen Golf IV Variant (1J5), 05\/1999–06\/2006 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-volkswagen\"\u003eVolkswagen\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F8592001 · F7908002). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eWhen the car is lowered more than 40 mm in combination with a drive shaft diameter more than 42 mm, please make sure that there is sufficient distance between the stabilizer and the drive shaft. It maybe necessary to install another anti-roll bar or other coupling rod.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437592900,"sku":"E10-85-001-15-22","price":185.61,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-15-014-01-22","title":"Eibach Pro-Kit Lowering Springs E10-15-014-01-22 – Audi A1 (8X1, 8XK, 8XA, 8XF)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-15-014-01-22 for the Audi A1 (8X1, 8XK), lowering the car by 20 mm, approved to 880 kg front and 840 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-15-014-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 880 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 840 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-15-014-01-VA, 2 × rear axle spring F11-85-008-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1015014.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Audi A1 (8X1, 8XK), 05\/2010–10\/2018, FWD; and Audi A1 Sportback (8XA, 8XF), 11\/2011–10\/2018, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-audi\"\u003eAudi\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-15-014-01-VA · 2 × rear axle spring F11-85-008-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437691204,"sku":"E10-15-014-01-22","price":163.59,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-42-065-01-22","title":"Eibach Pro-Kit Lowering Springs E10-42-065-01-22 – Genesis GV80 (JX1)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-42-065-01-22 for the Genesis GV80 (JX1), lowering the car by 30 mm at the front and 20 mm at the rear, approved to 1445 kg front and 1770 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-42-065-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1445 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1770 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-42-065-01-FA, F11-42-065-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1042065.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Genesis GV80 (JX1), from 06\/2020, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-42-065-01-FA · F11-42-065-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437953348,"sku":"E10-42-065-01-22","price":307.68,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-20-018-04-20","title":"Eibach Pro-Kit Lowering Springs E10-20-018-04-20 – BMW 5 Series, 7 Series","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-20-018-04-20 for the BMW 5 Gran Turismo (F07), lowering the car by 25 mm at the front and 10–20 mm at the rear, approved to 1340 kg front and 1500 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-20-018-04-20\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 10–20 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e550i, 550i xDrive:\u003c\/strong\u003e 25 mm front \/ 10–15 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e740d xDrive, 750i, 750i xDrive, 750d xDrive:\u003c\/strong\u003e 25 mm front \/ 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1340 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1500 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-20-018-02-VA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e air-spring adjustment\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1020018.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm at the front and 10–20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW 5 Gran Turismo (F07), 01\/2009–02\/2017, AWD; and BMW 7 (F01, F02, F03, F04), 02\/2008–12\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw-5-series\"\u003eBMW 5 Series\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-20-018-02-VA (the Eibach spring column also lists: air-spring adjustment)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411438018884,"sku":"E10-20-018-04-20","price":152.27,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-35-023-02-22","title":"Eibach Pro-Kit Lowering Springs E10-35-023-02-22 – Ford Focus III","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-35-023-02-22 for the Ford Focus III, lowering the car by 25 mm at the front and 10–25 mm at the rear, approved to 1100 kg front and 1060 kg rear axle load, covering 3 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-35-023-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 10–25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 Ti, 1.6 Flexifuel, 1.6 Ecoboost, 1.6 TDCi, 1.6 TDCi ECOnetic, 2.0, 2.0 Flex, 2.0 Ti…:\u003c\/strong\u003e 25 mm front \/ 25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 ST:\u003c\/strong\u003e 25 mm front \/ 10 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1100 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-84-006-07-VA, 2 × rear axle spring F11-35-014-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1035023.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 3 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm at the front and 10–25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Focus III, from 04\/2011; Ford Focus III, from 07\/2012; Ford Focus III Van\/Estate \/ Box\/Station Wagon, 04\/2011–08\/2014; and Ford Focus III Saloon \/ Saloon, 04\/2011–08\/2014 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford-focus\"\u003eFord Focus\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-84-006-07-VA · 2 × rear axle spring F11-35-014-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411438149956,"sku":"E10-35-023-02-22","price":189.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-60-013-07-22","title":"Eibach Pro-Kit Lowering Springs E10-60-013-07-22 – Mitsubishi Lancer (CY, Z\/A)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-60-013-07-22 for the Mitsubishi Lancer Saloon \/ Saloon (CY\/Z_A), lowering the car by 30 mm at the front and 25 mm at the rear, approved to 905 kg front and 980 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-60-013-07-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 905 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 980 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-60-016-01-VA, 2 × rear axle spring F11-60-013-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1060013.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mitsubishi Lancer Saloon \/ Saloon (CY\/Z_A), from 03\/2007 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mitsubishi-lancer\"\u003eMitsubishi Lancer\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-60-016-01-VA · 2 × rear axle spring F11-60-013-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411438248260,"sku":"E10-60-013-07-22","price":198.83,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e1024-140","title":"Eibach Pro-Kit Lowering Springs E1024-140","description":"\u003cp\u003eEibach Pro-Kit lowering springs E1024-140 for the Alfa Romeo GTV (916C_), lowering the car by 20 mm, approved to 1060 kg front and 1000 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E1024-140\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1000 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F1024001, F1018102\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1018-140.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Alfa Romeo GTV (916C_), 10\/1997–07\/2003; Alfa Romeo GTV (916C_), 08\/2003–10\/2005; Alfa Romeo Spider (916S_), 10\/1997–07\/2003; and Alfa Romeo Spider (916S_), 08\/2003–04\/2005 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F1024001 · F1018102). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411442442564,"sku":"E1024-140","price":247.9,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-70-018-01-22","title":"Eibach Pro-Kit Lowering Springs E10-70-018-01-22 – Peugeot 308 II (LB, LP, LW, LH)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-70-018-01-22 for the Peugeot 308 II, lowering the car by 15–30 mm at the front and 15–20 mm at the rear, approved to 1000 kg front and 900 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-70-018-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 15–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 15–20 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.2 THP 110, 1.2 THP 130, 1.2 VTi 72, 1.6, 1.6 THP 125, 1.6 THP 150, 1.6 THP 163, 1.6 V…:\u003c\/strong\u003e 30 mm front \/ 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 GTI, 1.6 GT 205:\u003c\/strong\u003e 15–20 mm front \/ 15 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1000 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 900 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-70-018-01-VA, 2 × rear axle spring F11-70-018-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1070018.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 15–30 mm at the front and 15–20 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Peugeot 308 II, from 09\/2013, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-70-018-01-VA · 2 × rear axle spring F11-70-018-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411442540868,"sku":"E10-70-018-01-22","price":199.46,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-79-012-03-22","title":"Eibach Pro-Kit Lowering Springs E10-79-012-03-22 – Škoda Superb III (3V5)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-79-012-03-22 for the Skoda Superb III Estate \/ Estate (3V5), lowering the car by 35 mm at the front and 30 mm at the rear, approved to 1120 kg front and 1253 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-79-012-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 35 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1120 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1253 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-85-041-01-VA, 2 × rear axle spring F11-79-008-01-HA, M45-85-014-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e ABE1015021.pdf, E1015021.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 35 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Skoda Superb III Estate \/ Estate (3V5), from 03\/2015, FWD; and Volkswagen Touran | Golf Touran (5T1), from 05\/2015 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-85-041-01-VA · 2 × rear axle spring F11-79-008-01-HA · M45-85-014-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411442704708,"sku":"E10-79-012-03-22","price":208.27,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/collections\/eibach-pro-kit-banner-v2.jpg?v=1792582739","url":"https:\/\/suspengo.com\/collections\/eibach-pro-kit.oembed?page=3","provider":"Suspengo","version":"1.0","type":"link"}