{"title":"Eibach Pro-Lift-Kit Lift Springs","description":"\u003cp\u003ePro-Lift-Kit does the opposite of a lowering spring: it raises the car for extra ground clearance and a more capable stance, while keeping the original dampers. Across the kits we stock the lift reaches up to 50 mm, depending on the vehicle. The extra clearance can also make room for a taller tyre, so check your arch and suspension clearances first.\u003c\/p\u003e\u003cp\u003e\u003ca href=\"\/collections\/eibach\"\u003eAll Eibach\u003c\/a\u003e · \u003ca href=\"\/pages\/vehicles\"\u003eBrowse by vehicle\u003c\/a\u003e · \u003ca href=\"\/pages\/parts-a-z\"\u003eParts A–Z\u003c\/a\u003e\u003c\/p\u003e","products":[{"product_id":"e30-20-020-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-20-020-02-22 – BMW X1 (E84)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-20-020-02-22 for the BMW X1 (E84), raising the car by 25–30 mm at the front and 30 mm at the rear, approved to 1030 kg front and 1220 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-20-020-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1030 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1220 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-20-020-02-FA, F31-20-020-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3020020.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–30 mm at the front and 30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW X1 (E84), 03\/2009–06\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw\"\u003eBMW\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-20-020-02-FA · F31-20-020-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433365828,"sku":"E30-20-020-02-22","price":302.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-20-024-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-20-024-01-22 – BMW X3, X4","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-20-024-01-22 for the BMW X3 (F25), raising the car by 30 mm, approved to 1120 kg front and 1330 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-20-024-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1120 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1330 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-20-024-01-FA, F31-20-024-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3020024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW X3 (F25), 09\/2010–08\/2017, AWD; and BMW X4 (F26), 04\/2014–03\/2018, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw\"\u003eBMW\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-20-024-01-FA · F31-20-024-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411433824580,"sku":"E30-20-024-01-22","price":302.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-20-024-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-20-024-02-22 – BMW X3, X4","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-20-024-02-22 for the BMW X3 (F25), raising the car by 30 mm, approved to 1180 kg front and 1330 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-20-024-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1180 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1330 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-20-024-02-FA, F31-20-024-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3020024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BMW X3 (F25), 09\/2010–08\/2017, AWD; and BMW X4 (F26), 04\/2014–03\/2018, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-bmw\"\u003eBMW\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-20-024-02-FA · F31-20-024-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411435528516,"sku":"E30-20-024-02-22","price":302.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-25-035-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-25-035-01-22 – Mercedes-Benz GLA (X156)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-25-035-01-22 for the Mercedes-Benz GLA-Class (X156), raising the car by 30–40 mm at the front and 25 mm at the rear, approved to 1125 kg front and 950 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-25-035-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30–40 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1125 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 950 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-25-035-01-VA, 2 × rear axle spring F31-25-035-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3025035.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30–40 mm at the front and 25 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mercedes-Benz GLA-Class (X156), from 12\/2013, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mercedes-benz\"\u003eMercedes-Benz\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-25-035-01-VA · 2 × rear axle spring F31-25-035-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003efor vehicles without AMG-suspension\u003c\/li\u003e\n  \u003cli\u003efor vehicles without \"OE Offroadpackage\"\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436052804,"sku":"E30-25-035-01-22","price":302.65,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-25-047-03-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-25-047-03-22 – Mercedes-Benz GLB (X247)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-25-047-03-22 for the Mercedes-Benz GLB-Class (X247), raising the car by 20 mm at the front and 30 mm at the rear, approved to 1230 kg front and 1270 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-25-047-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1230 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1270 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-25-047-02-FA, F31-25-047-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3025047.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 20 mm at the front and 30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mercedes-Benz GLB-Class (X247), from 08\/2019, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mercedes-benz\"\u003eMercedes-Benz\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-25-047-02-FA · F31-25-047-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411436609860,"sku":"E30-25-047-03-22","price":334.11,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-25-053-04-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-25-053-04-22 – Mercedes-Benz G-Class (W465)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-25-053-04-22 for the Mercedes-Benz G-Class (W465), raising the car by 30 mm, approved to 1600 kg front and 2000 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-25-053-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1600 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 2000 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-25-044-01-FA, F31-25-044-01-RA, AM10-25-044-01-01\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3025044.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M1025044.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mercedes-Benz G-Class (W465), from 04\/2024 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-mercedes-benz\"\u003eMercedes-Benz\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-25-044-01-FA · F31-25-044-01-RA · AM10-25-044-01-01). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eonly for cars with 4-doors\u003c\/li\u003e\n  \u003cli\u003ewheel base: 2890 mm\u003c\/li\u003e\n  \u003cli\u003enot for vehicles with bump-travel-dependent brake pressure reducers on rear axle (RA)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411437068612,"sku":"E30-25-053-04-22","price":420.93,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-26-003-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-26-003-02-22 – Dacia Duster (HS, HM)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-26-003-02-22 for the Dacia Duster (HS_), raising the car by 25 mm, approved to 1040 kg front and 1010 kg rear axle load, covering 4 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-26-003-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1040 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e up to 1050 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-26-003-01-VA, F31-26-003-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3026003.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 4 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Dacia Duster (HS_), 04\/2010–01\/2018, AWD; Dacia Duster Van, from 04\/2011, FWD; Dacia Duster (HM_), from 10\/2017, FWD; and Renault Duster (HS_), from 01\/2011 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-26-003-01-VA · F31-26-003-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411438051652,"sku":"E30-26-003-02-22","price":219.59,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-26-006-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-26-006-01-22 – Dacia Duster (PYM, PYN)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-26-006-01-22 for the Dacia Duster (PYM_, PYN_), raising the car by 30 mm, approved to 1015 kg front and 970 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-26-006-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1015 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 970 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-26-006-01-FA, F31-26-006-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3026006.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Dacia Duster (PYM_, PYN_), from 11\/2023 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-26-006-01-FA · F31-26-006-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003enot for vehicles with bump-travel-dependent brake pressure reducers on rear axle (RA)\u003c\/li\u003e\n  \u003cli\u003eWheelbase 2658 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411442770244,"sku":"E30-26-006-01-22","price":254.83,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-26-006-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-26-006-02-22 – Dacia Duster (PYM, PYN)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-26-006-02-22 for the Dacia Duster (PYM_, PYN_), raising the car by 30 mm at the front and 10 mm at the rear, approved to 1015 kg front and 980 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-26-006-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 10 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1015 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 980 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-26-006-01-FA, F31-26-006-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3026006.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm at the front and 10 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Dacia Duster (PYM_, PYN_), from 11\/2023 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-26-006-01-FA · F31-26-006-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eFor cars with rear live axle.\u003c\/li\u003e\n  \u003cli\u003enot for vehicles with bump-travel-dependent brake pressure reducers on rear axle (RA)\u003c\/li\u003e\n  \u003cli\u003eWheelbase 2658 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411443261764,"sku":"E30-26-006-02-22","price":250.42,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-26-006-03-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-26-006-03-22 – Dacia Duster (PYM, PYN)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-26-006-03-22 for the Dacia Duster (PYM_, PYN_), raising the car by 30 mm at the front and 15 mm at the rear, approved to 1015 kg front and 985 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-26-006-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 15 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1015 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 985 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-26-006-01-FA, F31-26-006-03-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3026006.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm at the front and 15 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Dacia Duster (PYM_, PYN_), from 11\/2023 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-26-006-01-FA · F31-26-006-03-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eFor cars with rear live axle.\u003c\/li\u003e\n  \u003cli\u003enot for vehicles with bump-travel-dependent brake pressure reducers on rear axle (RA)\u003c\/li\u003e\n  \u003cli\u003eWheelbase 2658 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411443753284,"sku":"E30-26-006-03-22","price":250.42,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-26-008-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-26-008-01-22 – Dacia Bigster","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-26-008-01-22 for the Dacia Bigster, raising the car by 30 mm at the front and 5 mm at the rear, approved to 1015 kg front and 995 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-26-008-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 5 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1015 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 995 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-26-006-01-FA, F31-26-008-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3026006.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm at the front and 5 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Dacia Bigster, from 10\/2024 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-26-006-01-FA · F31-26-008-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411444310340,"sku":"E30-26-008-01-22","price":219.59,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-34-001-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-34-001-01-22 – Ineos Grenadier (GM)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-34-001-01-22 for the Ineos Grenadier (GM), raising the car by 30 mm, approved to 1675 kg front and 2160 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-34-001-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1675 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 2160 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-34-001-01-FA, F31-34-001-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3034001.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ineos Grenadier (GM), from 08\/2022, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-34-001-01-FA · F31-34-001-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eonly for vehicles without winch on the front axle\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411444801860,"sku":"E30-34-001-01-22","price":351.72,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-34-001-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-34-001-02-22 – Ineos Grenadier (GM)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-34-001-02-22 for the Ineos Grenadier (GM), raising the car by 30 mm, approved to 1675 kg front and 2160 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-34-001-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1675 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 2160 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-34-001-02-FA, F31-34-001-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3034001.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ineos Grenadier (GM), from 08\/2022, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-34-001-02-FA · F31-34-001-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eonly for vehicles with winch on the front axle\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411445260612,"sku":"E30-34-001-02-22","price":351.72,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-036-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-036-01-22 – Ford Ranger III (TKE)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-036-01-22 for the Ford Ranger (TKE), raising the car by 30 mm, approved to 1550 kg front and 1850 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-036-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1550 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1850 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-036-01-FA, AM30-35-036-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035036.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M3035036.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Ranger (TKE), 04\/2011–02\/2019, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-036-01-FA · AM30-35-036-01-22). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eonly for cars with production date until 25.02.2019 and until FIN (vehicle identification number) 17 digit FIN at position 11 = letter K (production year 2019) 17 digit FIN at position 12 = letter K (production month February)\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411445817668,"sku":"E30-35-036-01-22","price":370.6,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-044-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-044-01-22 – Ford Edge","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-044-01-22 for the Ford Edge, raising the car by 30 mm at the front and 20 mm at the rear, approved to 1430 kg front and 1275 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-044-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1430 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1275 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-044-01-FA, F31-35-044-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035044.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm at the front and 20 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Edge, from 09\/2014, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-044-01-FA · F31-35-044-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411446276420,"sku":"E30-35-044-01-22","price":376.89,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-053-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-053-02-22 – Ford Bronco Sport","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-053-02-22 for the Ford Bronco Sport, raising the car by 25–30 mm at the front and 30 mm at the rear, approved to 1180 kg front and 1070 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-053-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1180 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1070 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-053-02-FA, F31-35-053-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e TB\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035053.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–30 mm at the front and 30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Bronco Sport, from 04\/2021, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-053-02-FA · F31-35-053-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eWheelbase 2670 mm\u003c\/li\u003e\n  \u003cli\u003eNot for vehicles with equipment line Wildtrak\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411446735172,"sku":"E30-35-053-02-22","price":295.09,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-062-03-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-062-03-22 – Ford Ranger (2AB)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-062-03-22 for the Ford Ranger (2AB), raising the car by 35–40 mm at the front and 30 mm at the rear, approved to 1530 kg front and 1710 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-062-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 35–40 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRaptor 3.0 EcoBoost 4x4:\u003c\/strong\u003e + 40 mm front \/ + 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eRaptor 2.0 EcoBlue 4x4:\u003c\/strong\u003e + 35 mm front \/ + 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1530 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1710 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-062-03-FA, F31-35-062-03-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e TTG35062.pdf, E3035062.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 35–40 mm at the front and 30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Ranger (2AB), from 11\/2022, AWD; and Ford Ranger (2AB), from 12\/2023, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-062-03-FA · F31-35-062-03-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411448144196,"sku":"E30-35-062-03-22","price":339.14,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-065-01-02","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-065-01-02 – Ford Transit Custom \/ VW Transporter \/ Ford Tourneo Custom","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-065-01-02 for the Ford Tourneo Custom V710 BUS (NXN), raising the car by 0 mm at the front and 20 mm at the rear, covering 5 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-065-01-02\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 0 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 2015 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e OE, F31-35-065-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e Serie\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035065.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 5 vehicles, 5 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 0 mm at the front and 20 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Tourneo Custom V710 BUS (NXN), from 12\/2023, AWD; Ford Transit Custom V710 Bus (NXN), from 04\/2024, AWD; Ford Transit Custom V710 Van (NRN), from 10\/2023, AWD; Volkswagen Transporter T7 \/ Caravelle T7 Bus (TV_, TW_), from 07\/2024; and Volkswagen Transporter T7 Van \/ Box (TV_, TW_), from 07\/2024 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (OE · F31-35-065-01-RA (the Eibach spring column also lists: Serie)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003ewheel base 3100 mm\u003c\/li\u003e\n  \u003cli\u003eFor vehicles with unladen axle loads of at least 950 kg on the rear axle\u003c\/li\u003e\n  \u003cli\u003eWheelbase 3500 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411448668484,"sku":"E30-35-065-01-02","price":176.81,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-065-01-20","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-065-01-20 – Ford Transit Custom \/ VW Transporter","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-065-01-20 for the Ford Transit Custom V710 Van (NRN), raising the car by 25–30 mm at the front and 0 mm at the rear, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-065-01-20\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 0 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1600 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-065-01-FA, OE\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e Serie\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035065.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–30 mm at the front and 0 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Transit Custom V710 Van (NRN), from 10\/2023, AWD; and Volkswagen Transporter T7 Van \/ Box (TV_, TW_), from 07\/2024 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford-transit\"\u003eFord Transit\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-065-01-FA · OE (the Eibach spring column also lists: Serie)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003ewheel base 3100 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411449160004,"sku":"E30-35-065-01-20","price":181.84,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-065-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-065-01-22 – Ford Transit Custom \/ VW Transporter","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-065-01-22 for the Ford Transit Custom V710 Van (NRN), raising the car by 25–30 mm at the front and 20 mm at the rear, approved to 1600 kg front and 2015 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-065-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1600 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 2015 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-065-01-FA, F31-35-065-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035065.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–30 mm at the front and 20 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Transit Custom V710 Van (NRN), from 10\/2023, AWD; and Volkswagen Transporter T7 Van \/ Box (TV_, TW_), from 07\/2024 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford-transit\"\u003eFord Transit\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-065-01-FA · F31-35-065-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003ewheel base 3100 mm\u003c\/li\u003e\n  \u003cli\u003eFor vehicles with unladen axle loads of at least 950 kg on the rear axle\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411449651524,"sku":"E30-35-065-01-22","price":351.72,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-065-02-20","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-065-02-20 – Ford Transit Custom \/ VW Transporter \/ Ford Tourneo Custom","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-065-02-20 for the Ford Tourneo Custom V710 BUS (NXN), raising the car by 25–35 mm at the front and 0 mm at the rear, covering 5 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-065-02-20\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–35 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 0 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 EcoBlue, 2.0 EcoBlue AWD, 2.0 TDI, 2.0 TDI 4Motion:\u003c\/strong\u003e + 25–30 mm front \/ 0 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 EcoBlue, 2.0 EcoBlue AWD, 2.0 TDI, 2.0 TDI 4Motion:\u003c\/strong\u003e + 30–35 mm front \/ 0 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1770 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-065-02-FA, OE\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring column also lists:\u003c\/strong\u003e Serie\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035065.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 5 vehicles, 5 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–35 mm at the front and 0 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Tourneo Custom V710 BUS (NXN), from 12\/2023, AWD; Ford Transit Custom V710 Bus (NXN), from 04\/2024, AWD; Ford Transit Custom V710 Van (NRN), from 10\/2023, AWD; Volkswagen Transporter T7 \/ Caravelle T7 Bus (TV_, TW_), from 07\/2024; and Volkswagen Transporter T7 Van \/ Box (TV_, TW_), from 07\/2024 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-065-02-FA · OE (the Eibach spring column also lists: Serie)). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003ewheel base 3100 mm\u003c\/li\u003e\n  \u003cli\u003eNot for vehicles with unladen axle loads of less than 1300 kg on the front axle (unladen weight of the driver (75 kg) must be taken into account)\u003c\/li\u003e\n  \u003cli\u003eWheelbase 3500 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411451683140,"sku":"E30-35-065-02-20","price":176.81,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-35-065-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-35-065-02-22 – Ford Transit Custom \/ VW Transporter \/ Ford Tourneo Custom","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-35-065-02-22 for the Ford Tourneo Custom V710 BUS (NXN), raising the car by 25–35 mm at the front and 20 mm at the rear, approved to 1770 kg front and 2015 kg rear axle load, covering 5 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-35-065-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–35 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 EcoBlue, 2.0 EcoBlue AWD, 2.0 TDI, 2.0 TDI 4Motion:\u003c\/strong\u003e + 25–30 mm front \/ + 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.0 EcoBlue, 2.0 EcoBlue AWD, 2.0 TDI, 2.0 TDI 4Motion:\u003c\/strong\u003e + 30–35 mm front \/ + 20 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1770 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 2015 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-35-065-02-FA, F31-35-065-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3035065.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 5 vehicles, 5 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–35 mm at the front and 20 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Ford Tourneo Custom V710 BUS (NXN), from 12\/2023, AWD; Ford Transit Custom V710 Bus (NXN), from 04\/2024, AWD; Ford Transit Custom V710 Van (NRN), from 10\/2023, AWD; Volkswagen Transporter T7 \/ Caravelle T7 Bus (TV_, TW_), from 07\/2024; and Volkswagen Transporter T7 Van \/ Box (TV_, TW_), from 07\/2024 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-ford\"\u003eFord\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-35-065-02-FA · F31-35-065-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003ewheel base 3100 mm\u003c\/li\u003e\n  \u003cli\u003eFor vehicles with unladen axle loads of at least 950 kg on the rear axle\u003c\/li\u003e\n  \u003cli\u003eNot for vehicles with unladen axle loads of less than 1300 kg on the front axle (unladen weight of the driver (75 kg) must be taken into account)\u003c\/li\u003e\n  \u003cli\u003eWheelbase 3500 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411452272964,"sku":"E30-35-065-02-22","price":351.72,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-40-012-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-40-012-02-22 – Honda CR (RE, RM)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-40-012-02-22 for the Honda CR-V III (RE), raising the car by 25 mm at the front and 30 mm at the rear, approved to 1220 kg front and 1055 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-40-012-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1220 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1055 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-40-012-02-FL, F31-40-012-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3040012.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm at the front and 30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Honda CR-V III (RE), from 10\/2006, AWD; and Honda CR-V IV (RM), from 01\/2012, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-40-012-02-FL · F31-40-012-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411452666180,"sku":"E30-40-012-02-22","price":276.22,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-402-003-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-402-003-01-22 – BAIC X75","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-402-003-01-22 for the BAIC X75, raising the car by 30 mm, approved to 1060 kg front and 1045 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-402-003-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1045 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-402-003-01-FA, F31-402-003-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e TB\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E30402003.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BAIC X75, from 04\/2023 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-402-003-01-FA · F31-402-003-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003eWheelbase 2800 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411453157700,"sku":"E30-402-003-01-22","price":308.94,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-402-004-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-402-004-02-22 – BAIC BJ30","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-402-004-02-22 for the BAIC BJ30, raising the car by 30 mm at the front and 20 mm at the rear, approved to 1105 kg front and 1115 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-402-004-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1105 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1115 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-79-013-05-FA, F31-79-013-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e TB\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E30402004.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm at the front and 20 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BAIC BJ30, from 04\/2024, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-79-013-05-FA · F31-79-013-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n  \u003cli\u003eWheelbase 2820 mm\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411453714756,"sku":"E30-402-004-02-22","price":307.68,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-402-005-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-402-005-01-22 – BAIC BJ40","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-402-005-01-22 for the BAIC BJ40, raising the car by 30 mm, approved to 1300 kg front and 1500 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-402-005-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1300 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1500 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-402-005-01-FA, F31-402-005-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e TTG30402005.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BAIC BJ40, from 11\/2023, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-402-005-01-FA · F31-402-005-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411454206276,"sku":"E30-402-005-01-22","price":311.45,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-404-001-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-404-001-01-22 – BAW 212","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-404-001-01-22 for the BAW 212, raising the car by 40 mm, approved to 1270 kg front and 1450 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-404-001-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 40 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 40 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1270 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1450 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-404-001-01-FA, F31-404-001-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 40 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits BAW 212, from 03\/2026, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-404-001-01-FA · F31-404-001-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411454697796,"sku":"E30-404-001-01-22","price":313.97,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-024-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-024-01-22 – Hyundai ix35 \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-024-01-22 for the Hyundai ix35 (LM, EL, ELH), raising the car by 25 mm, approved to 1200 kg front and 1090 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-024-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1200 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1090 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-42-024-01-VA, 2 × rear axle spring F31-42-024-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai ix35 (LM, EL, ELH), from 01\/2010, FWD; and Kia Sportage III (SL), from 07\/2010, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-42-024-01-VA · 2 × rear axle spring F31-42-024-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411455156548,"sku":"E30-42-024-01-22","price":308.94,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-024-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-024-02-22 – Hyundai ix35 \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-024-02-22 for the Hyundai ix35 (LM, EL, ELH), raising the car by 25 mm, approved to 1200 kg front and 1090 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-024-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1200 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1090 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-42-024-01-VA, 2 × rear axle spring F31-42-024-02-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai ix35 (LM, EL, ELH), from 01\/2010, AWD; and Kia Sportage III (SL), from 07\/2010, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-42-024-01-VA · 2 × rear axle spring F31-42-024-02-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411455615300,"sku":"E30-42-024-02-22","price":301.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-024-03-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-024-03-22 – Hyundai ix35 \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-024-03-22 for the Hyundai ix35 (LM, EL, ELH), raising the car by 25 mm, approved to 1200 kg front and 1090 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-024-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1200 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1090 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-42-024-03-VA, 2 × rear axle spring F31-42-024-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai ix35 (LM, EL, ELH), from 01\/2010, FWD; and Kia Sportage III (SL), from 07\/2010, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-42-024-03-VA · 2 × rear axle spring F31-42-024-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411456106820,"sku":"E30-42-024-03-22","price":308.94,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-024-04-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-024-04-22 – Hyundai ix35 \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-024-04-22 for the Hyundai ix35 (LM, EL, ELH), raising the car by 25 mm, approved to 1200 kg front and 1090 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-024-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1200 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1090 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-42-024-03-VA, 2 × rear axle spring F31-42-024-02-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042024.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai ix35 (LM, EL, ELH), from 01\/2010, AWD; and Kia Sportage III (SL), from 07\/2010, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-42-024-03-VA · 2 × rear axle spring F31-42-024-02-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411456565572,"sku":"E30-42-024-04-22","price":301.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-038-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-038-01-22 – Hyundai Tucson \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-038-01-22 for the Hyundai Tucson (TLE), raising the car by 25 mm, approved to 1280 kg front and 1150 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-038-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1280 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1150 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-038-01-FA, F31-42-038-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042038.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Tucson (TLE), from 06\/2015, AWD; and Kia Sportage IV (QL-QLE), from 09\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-038-01-FA · F31-42-038-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411457515844,"sku":"E30-42-038-01-22","price":332.85,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-038-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-038-02-22 – Hyundai Tucson \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-038-02-22 for the Hyundai Tucson (TLE), raising the car by 25 mm, approved to 1280 kg front and 1150 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-038-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1280 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1150 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-038-02-FA, F31-42-038-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042038.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Tucson (TLE), from 06\/2015, FWD; and Kia Sportage IV (QL-QLE), from 09\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-038-02-FA · F31-42-038-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411458007364,"sku":"E30-42-038-02-22","price":339.14,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-043-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-043-02-22 – Hyundai Kona I (OS, OSE, OSI)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-043-02-22 for the Hyundai Kona (OS), raising the car by 20 mm, approved to 1030 kg front and 1055 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-043-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1030 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1055 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-043-02-FA, F31-42-043-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042043.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 20 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Kona (OS), from 07\/2017, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-043-02-FA · F31-42-043-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411458466116,"sku":"E30-42-043-02-22","price":288.8,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-045-03-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-045-03-22 – Hyundai Santa Fe IV (TM, TMA)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-045-03-22 for the Hyundai Santa FE IV (TM, TMA), raising the car by 25 mm at the front and 25–30 mm at the rear, approved to 1300 kg front and 1395 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-045-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1300 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1395 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-045-03-FA, F31-42-045-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042045.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm at the front and 25–30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Santa FE IV (TM, TMA), from 02\/2018, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-045-03-FA · F31-42-045-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411458924868,"sku":"E30-42-045-03-22","price":345.43,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-053-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-053-01-22 – Hyundai Tucson \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-053-01-22 for the Hyundai Tucson (NX4E, NX4A), raising the car by 25–30 mm, approved to 1270 kg front and 1210 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-053-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDI (ohne\/without HEV 169 kw), 1.6 T-GDI Hybrid 48V, 2.0 MPI, 1.6 CRDi 1.6 CRDI H…:\u003c\/strong\u003e + 30 mm front \/ + 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDI HTRAC (ohne\/without HEV 169 kw), 1.6 T-GDI Hybrid 48V HTRAC, 2.0 MPI AWD, 2.0…:\u003c\/strong\u003e + 25–30mm front \/ + 25–30mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDI (ohne\/without HEV 169 kw), 1.6 T-GDI MHEV, 1.6 CRDI, 1.6 CRDI MHEV, 2.0 MPI:\u003c\/strong\u003e +30 mm front \/ +30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDI AWD (ohne\/without HEV 169 kw), 1.6 T-GDI MHEV AWD, 1.6 CRDI MHEV AWD, 2.0 MPI…:\u003c\/strong\u003e + 25–30 mm front \/ + 25–30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1270 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1210 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-053-01-FA, F31-42-053-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042053.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 4 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Tucson (NX4E, NX4A), 11\/2020–05\/2024, FWD; Hyundai Tucson (NX4E, NX4A), 11\/2020–05\/2024, AWD; Kia Sportage V (NQ5), from 11\/2021, AWD; and Kia Sportage V (NQ5), from 11\/2021 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-053-01-FA · F31-42-053-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411459449156,"sku":"E30-42-053-01-22","price":307.68,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-053-05-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-053-05-22 – Hyundai Tucson \/ Kia Sportage","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-053-05-22 for the Hyundai Tucson (NX4E, NX4A), raising the car by 25–30 mm, approved to 1270 kg front and 1210 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-053-05-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDI PHEV 4WD (195 kw Systemleistung \/ system performance):\u003c\/strong\u003e + 30 mm front \/ + 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDI PHEV 4WD (185\/195kw Systemleistung \/ system performance):\u003c\/strong\u003e + 25–30 mm front \/ + 25–30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1270 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1210 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-054-02-FA, F31-42-053-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042053.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Tucson (NX4E, NX4A), 11\/2020–05\/2024, AWD; and Kia Sportage V (NQ5), from 11\/2021, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-054-02-FA · F31-42-053-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411459907908,"sku":"E30-42-053-05-22","price":301.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-054-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-054-02-22 – Hyundai Santa Fe IV (TM, TMA)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-054-02-22 for the Hyundai Santa FE IV (TM, TMA), raising the car by 25 mm at the front and 20–30 mm at the rear, approved to 1375 kg front and 1460 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-054-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.2 CRDi (148 kw), 2.2 CRDi HTRAC (148 kw):\u003c\/strong\u003e + 25 mm front \/ + 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDI Hybrid, 1.6 T-GDI Hybrid HTRAC (nur\/only HEV):\u003c\/strong\u003e + 25 mm front \/ + 20–25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1375 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1460 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-054-02-FA, F31-42-054-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042054.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm at the front and 20–30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Hyundai Santa FE IV (TM, TMA), from 08\/2020, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-054-02-FA · F31-42-054-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411460563268,"sku":"E30-42-054-02-22","price":345.43,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-42-054-04-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-42-054-04-22 – Kia Sorento IV (MQ4, MQ4A)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-42-054-04-22 for the Kia Sorento IV (MQ4, MQ4A), raising the car by 25–30 mm at the front and 20–30 mm at the rear, approved to 1375 kg front and 1475 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-42-054-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20–30 mm, depending on engine\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e2.2 CRDI, 2.2 CRDI 4WD:\u003c\/strong\u003e + 30 mm front \/ + 30 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003e1.6 T-GDi, 1.6 T-GDi AWD (nur\/only HEV):\u003c\/strong\u003e + 25 mm front \/ + 20–25 mm rear\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1375 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1475 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-42-054-02-FA, F31-42-054-02-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3042054.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25–30 mm at the front and 20–30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Kia Sorento IV (MQ4, MQ4A), from 03\/2020, AWD; and Kia Sorento IV (MQ4, MQ4A), from 03\/2020 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-42-054-02-FA · F31-42-054-02-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411461054788,"sku":"E30-42-054-04-22","price":345.43,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-43-001-01-20","title":"Eibach Pro-Lift-Kit Lift Springs E30-43-001-01-20 – Isuzu D-MAX III (BTF)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-43-001-01-20 for the Isuzu D-MAX III (BTF), raising the car by 30 mm, approved to 1460 kg front and 1920 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-43-001-01-20\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1460 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1920 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-43-001-01-FA, AM30-43-001-01-02\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3043001.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M3043001.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Isuzu D-MAX III (BTF), from 11\/2019, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-43-001-01-FA · AM30-43-001-01-02). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411461579076,"sku":"E30-43-001-01-20","price":313.97,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-436-001-01-20","title":"Eibach Pro-Lift-Kit Lift Springs E30-436-001-01-20 – JAC T8 Pro","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-436-001-01-20 for the JAC T8 PRO \/ Shuailing T8 PRO, raising the car by 30 mm, approved to 1300 kg front and 1800 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-436-001-01-20\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1300 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1800 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-43-001-01-FA, AM30-436-001-01-02\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E30436001.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eFitting instructions:\u003c\/strong\u003e M30436001.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits JAC T8 PRO \/ Shuailing T8 PRO, from 10\/2020, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-43-001-01-FA · AM30-436-001-01-02). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411462070596,"sku":"E30-436-001-01-20","price":433.52,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-46-006-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-46-006-01-22 – Kia Sorento I (JC)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-46-006-01-22 for the Kia Sorento I (JC), raising the car by 30 mm, approved to 1350 kg front and 1500 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-46-006-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1350 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1500 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-46-006-01-VA, 2 × rear axle spring F31-46-006-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3046006.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Kia Sorento I (JC), 08\/2002–11\/2012, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-46-006-01-VA · 2 × rear axle spring F31-46-006-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411462529348,"sku":"E30-46-006-01-22","price":292.58,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-46-028-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-46-028-01-22 – Kia Sorento III (UM)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-46-028-01-22 for the Kia Sorento III (UM), raising the car by 25 mm at the front and 35 mm at the rear, approved to 1350 kg front and 1450 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-46-028-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 35 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1350 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1450 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-46-028-01-FA, F31-46-028-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3046028.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm at the front and 35 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Kia Sorento III (UM), from 01\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-46-028-01-FA · F31-46-028-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411465707844,"sku":"E30-46-028-01-22","price":332.85,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-51-018-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-51-018-01-22 – Jeep Renegade (BU, B1, BV)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-51-018-01-22 for the Jeep Renegade (BU), raising the car by 25 mm, approved to 1160 kg front and 1060 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-51-018-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1160 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-51-018-01-FA, F31-51-018-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3051018.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Jeep Renegade (BU), from 07\/2014, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-51-018-01-FA · F31-51-018-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eNot for \"Trailhawk\"\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411466133828,"sku":"E30-51-018-01-22","price":288.8,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-51-018-03-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-51-018-03-22 – Jeep Renegade (BU, B1, BV)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-51-018-03-22 for the Jeep Renegade (BU), raising the car by 20 mm at the front and 25 mm at the rear, approved to 1160 kg front and 1060 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-51-018-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1160 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1060 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-51-018-03-FA, F31-51-018-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3051018.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 20 mm at the front and 25 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Jeep Renegade (BU), from 07\/2014, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-51-018-03-FA · F31-51-018-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eNot for \"Trailhawk\"\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411466592580,"sku":"E30-51-018-03-22","price":288.8,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-60-022-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-60-022-01-22 – Mitsubishi Outlander IV (GM_W, GG_W, DG)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-60-022-01-22 for the Mitsubishi Outlander IV (GM_W, GG_W, DG), raising the car by 20–25 mm, approved to 1390 kg front and 1550 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-60-022-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20–25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20–25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1390 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1550 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-60-022-01-FA, F31-60-022-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e TTG3060022.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 20–25 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Mitsubishi Outlander IV (GM_W, GG_W, DG), from 01\/2025 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-60-022-01-FA · F31-60-022-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411467936068,"sku":"E30-60-022-01-22","price":307.05,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-63-027-02-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-63-027-02-22 – Nissan Qashqai II (J11)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-63-027-02-22 for the Nissan Qashqai II (J11), raising the car by 30 mm at the front and 20 mm at the rear, approved to 1230 kg front and 995 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-63-027-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 20 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1230 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 995 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-63-027-02-VA, 2 × rear axle spring F31-63-027-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3063027.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm at the front and 20 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Nissan Qashqai II (J11), from 02\/2014, FWD; and Renault Kadjar (RFE), from 06\/2015 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-nissan-qashqai\"\u003eNissan Qashqai\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-63-027-02-VA · 2 × rear axle spring F31-63-027-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n  \u003cli\u003eFor cars with rear live axle.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411468394820,"sku":"E30-63-027-02-22","price":295.09,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-63-027-03-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-63-027-03-22 – Nissan Qashqai \/ Renault Kadjar","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-63-027-03-22 for the Nissan Qashqai II (J11), raising the car by 30 mm, approved to 1230 kg front and 1024 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-63-027-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1230 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1024 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-63-027-02-VA, 2 × rear axle spring F31-63-027-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3063027.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Nissan Qashqai II (J11), from 02\/2014, AWD; and Renault Kadjar (RFE), from 06\/2015, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-nissan-qashqai\"\u003eNissan Qashqai\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-63-027-02-VA · 2 × rear axle spring F31-63-027-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eFor cars with independent suspension at the rear axle.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411468853572,"sku":"E30-63-027-03-22","price":287.54,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-63-028-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-63-028-01-22 – Nissan X-Trail III (T32)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-63-028-01-22 for the Nissan X-Trail III (T32), raising the car by 25 mm at the front and 25–30 mm at the rear, approved to 1230 kg front and 1315 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-63-028-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1230 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1315 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F31-63-027-02-VA, F31-63-028-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3063027.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 25 mm at the front and 25–30 mm at the rear to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Nissan X-Trail III (T32), from 12\/2013, AWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F31-63-027-02-VA · F31-63-028-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411469312324,"sku":"E30-63-028-01-22","price":301.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"},{"product_id":"e30-71-007-01-22","title":"Eibach Pro-Lift-Kit Lift Springs E30-71-007-01-22 – Land Rover Discovery Sport (L550)","description":"\u003cp\u003eEibach Pro-Lift-Kit lift springs E30-71-007-01-22 for the Land Rover Discovery Sport (L550), raising the car by 30 mm, approved to 1340 kg front and 1510 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Lift-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E30-71-007-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1340 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1510 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F31-71-007-01-FA, F31-71-007-01-RA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E3071007.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Lift-Kit raises ride height by 30 mm to gain ground clearance and fit larger tyres, without the harshness of a full off-road conversion. Spring rates are matched to the standard dampers so the car keeps its on-road manners while sitting higher.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Land Rover Discovery Sport (L550), from 12\/2014 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eThe full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Lift-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F31-71-007-01-FA · F31-71-007-01-RA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept electronic suspension systems.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411469771076,"sku":"E30-71-007-01-22","price":376.89,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-lift-kit-lifting-springs-clean.jpg?v=1791831021"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/collections\/eibach-pro-lift-kit-banner.jpg?v=1792582739","url":"https:\/\/suspengo.com\/collections\/eibach-pro-lift-kit.oembed?page=3","provider":"Suspengo","version":"1.0","type":"link"}