{"title":"Renault Scénic Shock Absorbers \u0026 Suspension","description":"\u003cp\u003eSuspension for the Renault Scénic across the Mk1 (JA), Mk2 (JM) and Mk3 (JZ) generations, including the Grand versions. Everything stocked is Bilstein: \u003ca href=\"\/collections\/suspension-renault-scenic\/series-b4\"\u003eB4\u003c\/a\u003e as the standard-height replacement, \u003ca href=\"\/collections\/suspension-renault-scenic\/series-b6\"\u003eB6\u003c\/a\u003e as the firmer alternative, and \u003ca href=\"\/collections\/suspension-renault-scenic\/series-b1\"\u003eprotection kits\u003c\/a\u003e alongside.\u003c\/p\u003e\n\u003ch2\u003eWhich variants this covers\u003c\/h2\u003e\n\u003cp\u003eThree generations are listed — JA, JM and JZ — covering both the standard Scénic and the longer Grand versions, all front-wheel drive. The Grand carries more weight behind the rear axle and is specified accordingly, so the two are not interchangeable at the back even within the same generation. Identify the car by chassis code rather than by registration year.\u003c\/p\u003e\n\u003ch2\u003eChoosing between the ranges\u003c\/h2\u003e\n\u003cp\u003eThe selection here is small and the decision correspondingly simple. \u003ca href=\"\/collections\/suspension-renault-scenic\/series-b4\"\u003eBilstein B4\u003c\/a\u003e is what the great majority of these need: an MPV bought to carry people and their belongings, where restoring the ride it had when new is the whole point. It fits at the original height on the existing springs. \u003ca href=\"\/collections\/suspension-renault-scenic\/series-b6\"\u003eBilstein B6\u003c\/a\u003e is the firmer choice at that same height and makes sense on a Grand that is routinely full, where the extra damping control stops the back end feeling loose over crests. No Tein ranges and no lowering or coilover options are listed for the Scénic, which is reasonable for the type of vehicle — there is nothing here to tempt an owner into a setup that would make it worse at its job.\u003c\/p\u003e\n\u003ch2\u003eWhat to check before ordering\u003c\/h2\u003e\n\u003cp\u003eReplace across each axle and have the tracking reset afterwards. On this car the strut top bearing deserves specific attention: Renault MPVs of this era commonly fail there first, and the resulting knock and heavy steering get blamed on the dampers more often than not. Inspect it while the strut is out and renew it with the \u003ca href=\"\/collections\/suspension-renault-scenic\/series-b1\"\u003eprotection kit\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch2\u003eCommon questions for this chassis\u003c\/h2\u003e\n\u003cp\u003e\u003cstrong\u003eIs Tein available for the Scénic?\u003c\/strong\u003e No. This page is Bilstein only.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eScénic and Grand Scénic the same?\u003c\/strong\u003e Not at the rear — the Grand is specified for more weight.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKnocking over bumps?\u003c\/strong\u003e Check the strut top bearing before replacing the damper.\u003c\/p\u003e","products":[{"product_id":"bilstein-shock-absorber-19-155876","title":"Bilstein B4 Shock Absorbers 19-155876 – Renault Grand Scénic, Scénic","description":"\u003cp\u003eBilstein B4 OEM Replacement shock absorber for the Renault Grand Scenic 2 and Scenic 3 — Bilstein Shock Absorber 19-155876.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Gas Pressure\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSeries:\u003c\/strong\u003e B4 OEM Replacement\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB4 is Bilstein's OE-replacement damper: valving matched to the car's original specification so ride height, body control and comfort return to how the vehicle left the factory. Nothing is uprated and nothing is lowered — it is the right choice when worn dampers have made the car float, bounce or wander, and you want factory behaviour back rather than a firmer setup.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Grand Scenic 2 (JM0-1), 04\/2004–06\/2009, FWD and Renault Scenic 3 (JZ0-1), 12\/2008–09\/2016, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above. \u003cstrong\u003eOEM References:\u003c\/strong\u003e 562100018R, 82 00 038 260, 82 00 181 921, 82 00 309 846, 82 00 330 197, 82 00 415 734 and 5 more.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B4 damper unit — a single shock absorber, not a pair and not an axle set. Order two to do an axle, four for the whole car. Bump stops, dust covers, top mounts and fixings are not included.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes correct installation, the correct tightening torques, and serviceable bump stops and dust covers. A damper run without its protection parts will be scored by road grit — that is wear, not a defect. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56615462666564,"sku":"19-155876","price":64.87,"currency_code":"EUR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/22-147530_1_0f6ffc7e-2022-457c-93b3-65bc9432c7a7.jpg?v=1781430212"},{"product_id":"bilstein-shock-absorber-19-277288","title":"Bilstein B4 Shock Absorbers 19-277288 – Renault Scénic IV (J9)","description":"\u003cp\u003eBilstein Rear (universal) shock absorber — Bilstein Shock Absorber 19-277288\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting Position:\u003c\/strong\u003e Rear (universal)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Gas Pressure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDamping System:\u003c\/strong\u003e Twin-Tube\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e bottom eye\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB4 is Bilstein's OE-replacement damper: valving matched to the car's original specification so ride height, body control and comfort return to how the vehicle left the factory. Nothing is uprated and nothing is lowered — it is the right choice when worn dampers have made the car float, bounce or wander, and you want factory behaviour back rather than a firmer setup. This unit is twin-tube, the construction Bilstein specifies where the original fitment used it.\u003c\/p\u003e\n\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Scenic 4 (J9), 09\/2016–07\/2022, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above. \u003cstrong\u003eOEM References:\u003c\/strong\u003e 562100018R, 56210022R, 562102387R, 562102469R, 562100034R.\u003c\/p\u003e\n\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B4 damper unit for the rear axle (either side) — a single shock absorber, not a pair and not an axle set. Order two to do an axle, four for the whole car. Mounting is bottom eye. Bump stops, dust covers, top mounts and fixings are not included.\u003c\/p\u003e\n\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes correct installation, the correct tightening torques, and serviceable bump stops and dust covers. A damper run without its protection parts will be scored by road grit — that is wear, not a defect. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56615535083844,"sku":"19-277288","price":80.93,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/19-277288_1.jpg?v=1779441292"},{"product_id":"bilstein-shock-absorber-22-225269","title":"Bilstein B4 Shock Absorbers 22-225269 – Renault Grand Scénic, Scénic","description":"\u003cp\u003eBilstein Front (universal) shock absorber — Bilstein Shock Absorber 22-225269\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting Position:\u003c\/strong\u003e Front (universal)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Gas Pressure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDamping System:\u003c\/strong\u003e Twin-Tube\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Top pin\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB4 is Bilstein's OE-replacement damper: valving matched to the car's original specification so ride height, body control and comfort return to how the vehicle left the factory. Nothing is uprated and nothing is lowered — it is the right choice when worn dampers have made the car float, bounce or wander, and you want factory behaviour back rather than a firmer setup. This unit is twin-tube, the construction Bilstein specifies where the original fitment used it.\u003c\/p\u003e\n\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Scenic 3 (JZ0-1), 12\/2008–09\/2016, FWD and Renault Grand Scenic 3 (JZ0-1), 02\/2009–09\/2016, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above. \u003cstrong\u003eOEM References:\u003c\/strong\u003e 543022646R, 543025246R, 543020017R.\u003c\/p\u003e\n\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B4 damper unit for the front axle (either side) — a single shock absorber, not a pair and not an axle set. Order two to do an axle, four for the whole car. Mounting is top pin. Bump stops, dust covers, top mounts and fixings are not included.\u003c\/p\u003e\n\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes correct installation, the correct tightening torques, and serviceable bump stops and dust covers. A damper run without its protection parts will be scored by road grit — that is wear, not a defect. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56615609401668,"sku":"22-225269","price":84.1,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/22-225269_1.jpg?v=1779441382"},{"product_id":"bilstein-shock-absorber-22-277275","title":"Bilstein B4 Shock Absorbers 22-277275 – Renault Grand Scénic, Scénic","description":"\u003cp\u003eBilstein Front (universal) shock absorber — Bilstein Shock Absorber 22-277275\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting Position:\u003c\/strong\u003e Front (universal)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Gas Pressure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDamping System:\u003c\/strong\u003e Twin-Tube\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Top pin\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB4 is Bilstein's OE-replacement damper: valving matched to the car's original specification so ride height, body control and comfort return to how the vehicle left the factory. Nothing is uprated and nothing is lowered — it is the right choice when worn dampers have made the car float, bounce or wander, and you want factory behaviour back rather than a firmer setup. This unit is twin-tube, the construction Bilstein specifies where the original fitment used it.\u003c\/p\u003e\n\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Grand Scenic 4 (R9), 09\/2016–03\/2023, FWD and Renault Scenic 4 (J9), 09\/2016–07\/2022, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above. \u003cstrong\u003eOEM References:\u003c\/strong\u003e 543021249R.\u003c\/p\u003e\n\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B4 damper unit for the front axle (either side) — a single shock absorber, not a pair and not an axle set. Order two to do an axle, four for the whole car. Mounting is top pin. Bump stops, dust covers, top mounts and fixings are not included.\u003c\/p\u003e\n\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes correct installation, the correct tightening torques, and serviceable bump stops and dust covers. A damper run without its protection parts will be scored by road grit — that is wear, not a defect. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56615645708612,"sku":"22-277275","price":68.76,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/22-277275_1.jpg?v=1779441443"},{"product_id":"bilstein-shock-absorber-22-283054","title":"Bilstein B4 Shock Absorbers 22-283054 – Renault Scénic IV (J9)","description":"\u003cp\u003eBilstein Front (universal) shock absorber — Bilstein Shock Absorber 22-283054\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFitting Position:\u003c\/strong\u003e Front (universal)\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Gas Pressure\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDamping System:\u003c\/strong\u003e Twin-Tube\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Top pin\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB4 is Bilstein's OE-replacement damper: valving matched to the car's original specification so ride height, body control and comfort return to how the vehicle left the factory. Nothing is uprated and nothing is lowered — it is the right choice when worn dampers have made the car float, bounce or wander, and you want factory behaviour back rather than a firmer setup. This unit is twin-tube, the construction Bilstein specifies where the original fitment used it.\u003c\/p\u003e\n\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Scenic 4 (J9), 09\/2016–07\/2022, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above. \u003cstrong\u003eOEM References:\u003c\/strong\u003e 543022368R.\u003c\/p\u003e\n\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B4 damper unit for the front axle (either side) — a single shock absorber, not a pair and not an axle set. Order two to do an axle, four for the whole car. Mounting is top pin. Bump stops, dust covers, top mounts and fixings are not included.\u003c\/p\u003e\n\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes correct installation, the correct tightening torques, and serviceable bump stops and dust covers. A damper run without its protection parts will be scored by road grit — that is wear, not a defect. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56615648493892,"sku":"22-283054","price":68.07,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/22-283054_1.jpg?v=1779441449"},{"product_id":"bilstein-shock-absorber-22-277268","title":"Bilstein B6 Shock Absorbers 22-277268 – Renault Grand Scénic, Scénic","description":"\u003cp\u003eBilstein B6 Performance shock absorber for the Renault Grand Scenic 4 and Scenic 4 — Bilstein Shock Absorber 22-277268.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Gas Pressure\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSeries:\u003c\/strong\u003e B6 Performance\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB6 is the uprated damper for a car kept at standard ride height. Bilstein firms up the valving over the OE curve, so body roll settles sooner, the nose dives less under braking and the car tracks straighter at speed. You feel more of the road surface than with B4, which is the point — it is a handling upgrade, not a comfort one, and it needs no springs to work.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Grand Scenic 4 (R9), 09\/2016–03\/2023, FWD and Renault Scenic 4 (J9), 09\/2016–07\/2022, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B6 damper unit — a single shock absorber, not a pair and not an axle set. Order two to do an axle, four for the whole car. Bump stops, dust covers, top mounts and fixings are not included.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes correct installation, the correct tightening torques, and serviceable bump stops and dust covers. A damper run without its protection parts will be scored by road grit — that is wear, not a defect. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56615728644420,"sku":"22-277268","price":124.71,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/22-277268_1.jpg?v=1779441444"},{"product_id":"bilstein-shock-absorber-24-266369","title":"Bilstein B6 Shock Absorbers 24-266369 – Renault Grand Scénic, Mégane, Scénic","description":"\u003cp\u003eBilstein B6 Performance shock absorber for the Renault Grand Scenic 4, Megane 4 Saloon and Scenic 4 — Bilstein Shock Absorber 24-266369.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType:\u003c\/strong\u003e Gas Pressure\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSeries:\u003c\/strong\u003e B6 Performance\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB6 is the uprated damper for a car kept at standard ride height. Bilstein firms up the valving over the OE curve, so body roll settles sooner, the nose dives less under braking and the car tracks straighter at speed. You feel more of the road surface than with B4, which is the point — it is a handling upgrade, not a comfort one, and it needs no springs to work.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Grand Scenic 4 (R9), 09\/2016–03\/2023, FWD, Renault Megane 4 Saloon (LVA-M-N), from 10\/2016, FWD and Renault Scenic 4 (J9), 09\/2016–07\/2022, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B6 damper unit — a single shock absorber, not a pair and not an axle set. Order two to do an axle, four for the whole car. Bump stops, dust covers, top mounts and fixings are not included.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes correct installation, the correct tightening torques, and serviceable bump stops and dust covers. A damper run without its protection parts will be scored by road grit — that is wear, not a defect. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56615820329284,"sku":"24-266369","price":135.86,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/24-266369_1.jpg?v=1779441518"},{"product_id":"bilstein-suspension-strut-support-bearing-12-238163","title":"Bilstein B1 Strut Support Bearing 12-238163 – Renault Mégane, Grand Scénic, Scénic","description":"\u003cp\u003eBilstein B1 Suspension strut support bearing for 6 Renault models — Bilstein Suspension strut support bearing 12-238163.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e BILSTEIN\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHS\/CN Code:\u003c\/strong\u003e 40 169 952\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 1.27 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB1 is Bilstein's suspension service range — the protection kits, bump stops, dust covers and strut support bearings that sit around the damper. They are wear parts: a collapsed bump stop or split dust cover lets grit onto the piston rod and will kill a new damper early. Built to the same standards as the dampers they protect, and worth replacing at the same time.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits 6 Renault models including Megane 3 (BZ0-1, B3) and Megane 3 Coupe (DZ0-1) — see the full list below. Verify fitment using the vehicle compatibility checker above. \u003cstrong\u003eOEM References:\u003c\/strong\u003e 54 3A 068 74R, 54 3A 068 74R SK\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B1 strut support bearing — a single corner. Order two to do an axle. The strut, spring and top nut are not included.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes the bearing is fitted with the top nut torqued to specification and the strut re-assembled correctly. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56618289856836,"sku":"12-238163","price":75.99,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/bilstein-strut-support-bearing_094.jpg?v=1786996777"},{"product_id":"bilstein-suspension-strut-support-bearing-12-303892","title":"Bilstein B1 Strut Support Bearing 12-303892 – Renault Espace, Grand Scénic and more","description":"\u003cp\u003eBilstein B1 Suspension strut support bearing for 4 Renault models — Bilstein Suspension strut support bearing 12-303892.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e BILSTEIN\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eHS\/CN Code:\u003c\/strong\u003e 40 169 952\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eWeight:\u003c\/strong\u003e 0.52 kg\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003eB1 is Bilstein's suspension service range — the protection kits, bump stops, dust covers and strut support bearings that sit around the damper. They are wear parts: a collapsed bump stop or split dust cover lets grit onto the piston rod and will kill a new damper early. Built to the same standards as the dampers they protect, and worth replacing at the same time.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits 4 Renault models including Espace 5 (JR) and Talisman (LP) — see the full list below. Verify fitment using the vehicle compatibility checker above. \u003cstrong\u003eOEM References:\u003c\/strong\u003e 54 32 070 20R\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne Bilstein B1 strut support bearing — a single corner. Order two to do an axle. The strut, spring and top nut are not included.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Bilstein's manufacturer warranty against defects in materials and workmanship. Cover assumes the bearing is fitted with the top nut torqued to specification and the strut re-assembled correctly. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e","brand":"Bilstein","offers":[{"title":"Default Title","offer_id":56618310598980,"sku":"12-303892","price":21.39,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/bilstein-strut-support-bearing_232.jpg?v=1786997195"},{"product_id":"e10-75-005-01-22","title":"Eibach Pro-Kit Lowering Springs E10-75-005-01-22 – Renault Scénic II (JM0, 1)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-75-005-01-22 for the Renault Scénic II (JM0\/1_), lowering the car by 30 mm, approved to 1130 kg front and 1025 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-75-005-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1130 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1025 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-75-003-01-VA, 2 × rear axle spring F11-75-005-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1075005.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Scénic II (JM0\/1_), 06\/2003–10\/2007 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-renault\"\u003eRenault\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-75-003-01-VA · 2 × rear axle spring F11-75-005-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411505586500,"sku":"E10-75-005-01-22","price":200.71,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-75-005-02-22","title":"Eibach Pro-Kit Lowering Springs E10-75-005-02-22 – Renault Scénic II (JM0, 1)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-75-005-02-22 for the Renault Scénic II (JM0\/1_), lowering the car by 30 mm, approved to 1185 kg front and 1025 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-75-005-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1185 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1025 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-75-003-02-VA, 2 × rear axle spring F11-75-005-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1075005.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 30 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Scénic II (JM0\/1_), 06\/2003–10\/2007 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-renault\"\u003eRenault\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-75-003-02-VA · 2 × rear axle spring F11-75-005-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411506733380,"sku":"E10-75-005-02-22","price":200.71,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-75-014-01-22","title":"Eibach Pro-Kit Lowering Springs E10-75-014-01-22 – Renault Scénic III (JZ0, 1)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-75-014-01-22 for the Renault Scénic III (JZ0\/1_), lowering the car by 20–30 mm at the front and 25 mm at the rear, approved to 1110 kg front and 1065 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-75-014-01-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 20–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1110 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1065 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-75-012-02-VA, 2 × rear axle spring F11-75-014-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1075012.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 20–30 mm at the front and 25 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Scénic III (JZ0\/1_), from 02\/2009 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-renault\"\u003eRenault\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-75-012-02-VA · 2 × rear axle spring F11-75-014-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411536617796,"sku":"E10-75-014-01-22","price":169.25,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-75-014-02-22","title":"Eibach Pro-Kit Lowering Springs E10-75-014-02-22 – Renault Scénic III (JZ0, 1)","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-75-014-02-22 for the Renault Scénic III (JZ0\/1_), lowering the car by 25 mm, approved to 1230 kg front and 1065 kg rear axle load.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-75-014-02-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 25 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1230 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1065 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e 2 × front axle spring F11-75-014-02-VA, 2 × rear axle spring F11-75-014-01-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1075012.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 1 vehicle, 1 fitment row\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25 mm on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Scénic III (JZ0\/1_), from 02\/2009 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-renault\"\u003eRenault\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (2 × front axle spring F11-75-014-02-VA · 2 × rear axle spring F11-75-014-01-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411537568068,"sku":"E10-75-014-02-22","price":180.58,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-75-022-03-22","title":"Eibach Pro-Kit Lowering Springs E10-75-022-03-22 – Renault Grand Scénic, Scénic","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-75-022-03-22 for the Renault Grand Scénic IV (R9_), lowering the car by 25–30 mm at the front and 30 mm at the rear, approved to 1150 kg front and 1294 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-75-022-03-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1150 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1294 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-75-022-01-FA, 2 × rear axle spring F11-75-014-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1075020.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25–30 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Grand Scénic IV (R9_), from 09\/2016; and Renault Scénic IV (J9_), from 09\/2016 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-renault\"\u003eRenault\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-75-022-01-FA · 2 × rear axle spring F11-75-014-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411553132868,"sku":"E10-75-022-03-22","price":198.83,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"},{"product_id":"e10-75-022-04-22","title":"Eibach Pro-Kit Lowering Springs E10-75-022-04-22 – Renault Grand Scénic, Scénic","description":"\u003cp\u003eEibach Pro-Kit lowering springs E10-75-022-04-22 for the Renault Grand Scénic IV (R9_), lowering the car by 25–30 mm at the front and 30 mm at the rear, approved to 1230 kg front and 1294 kg rear axle load, covering 2 vehicle variants in the Eibach application list.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003e\n\u003cstrong\u003eManufacturer:\u003c\/strong\u003e Eibach\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eProduct line:\u003c\/strong\u003e Pro-Kit\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePart number:\u003c\/strong\u003e E10-75-022-04-22\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, front:\u003c\/strong\u003e 25–30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eLowering, rear:\u003c\/strong\u003e 30 mm\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, front:\u003c\/strong\u003e 1230 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003ePermitted axle load, rear:\u003c\/strong\u003e 1294 kg\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eSpring part numbers:\u003c\/strong\u003e F11-75-022-02-FA, 2 × rear axle spring F11-75-014-03-HA\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eType-approval marking:\u003c\/strong\u003e T\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eCertificate document:\u003c\/strong\u003e E1075020.pdf\u003c\/li\u003e\n  \u003cli\u003e\n\u003cstrong\u003eApplications covered:\u003c\/strong\u003e 2 vehicles, 2 fitment rows\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003ePerformance\u003c\/h3\u003e\n\u003cp\u003ePro-Kit is Eibach's progressive-rate lowering spring set. It drops the car by 25–30 mm at the front and 30 mm at the rear on the standard dampers, so the centre of gravity falls and body roll through a corner is reduced without turning the ride harsh. The progressive rate stays compliant over small bumps and firms up as the spring compresses, which is what keeps the car usable on poor roads while still feeling tied down at speed.\u003c\/p\u003e\n\u003ch3\u003eFitment\u003c\/h3\u003e\n\u003cp\u003eFits Renault Grand Scénic IV (R9_), from 09\/2016; and Renault Scénic IV (J9_), from 09\/2016 — see the full list below. Verify fitment using the vehicle compatibility checker above.\u003c\/p\u003e\n\u003cp\u003eBrowse every suspension part we list for this car in the \u003ca href=\"\/collections\/suspension-renault\"\u003eRenault\u003c\/a\u003e collection. The full Eibach range and what each line is for is set out on our \u003ca href=\"\/pages\/eibach-ranges\"\u003eEibach ranges\u003c\/a\u003e page.\u003c\/p\u003e\n\u003ch3\u003eWhat's Included\u003c\/h3\u003e\n\u003cp\u003eOne complete Eibach Pro-Kit spring set for this vehicle — springs for both axles, supplied together as a matched front-and-rear set (F11-75-022-02-FA · 2 × rear axle spring F11-75-014-03-HA). Dampers, top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.\u003c\/p\u003e\n\u003ch3\u003eWarranty\u003c\/h3\u003e\n\u003cp\u003eBacked by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.\u003c\/p\u003e\n\u003ch3\u003eNotes\u003c\/h3\u003e\n\u003cul\u003e\n  \u003cli\u003eIf not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.\u003c\/li\u003e\n  \u003cli\u003eThe specifications indicated in the Components Certificate are for the classification of the item \/ vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter \"K\" in your vehicle registration certificate or to find at the type plate of your car!)\u003c\/li\u003e\n  \u003cli\u003ePlease verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de\u003c\/li\u003e\n  \u003cli\u003eIn case of non-conformance the items must not be fitted – please refer to your dealer.\u003c\/li\u003e\n  \u003cli\u003eMounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.\u003c\/li\u003e\n  \u003cli\u003eMounting position - you can \"read\" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.\u003c\/li\u003e\n  \u003cli\u003eWheel adjustment - after completion of the spring\/suspension installation, checking the wheel adjustment is required.\u003c\/li\u003e\n  \u003cli\u003eShock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.\u003c\/li\u003e\n  \u003cli\u003eThe installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8\u003c\/li\u003e\n  \u003cli\u003eHere all wheel\/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.\u003c\/li\u003e\n  \u003cli\u003eDepending on engine, gearbox\/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.\u003c\/li\u003e\n  \u003cli\u003eThe applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.\u003c\/li\u003e\n  \u003cli\u003eIf your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage\/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.\u003c\/li\u003e\n  \u003cli\u003eWithout levelling control.\u003c\/li\u003e\n  \u003cli\u003eExcept vehicels with 4WD.\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Eibach","offers":[{"title":"Default Title","offer_id":57411553591620,"sku":"E10-75-022-04-22","price":188.13,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0963\/9664\/0580\/files\/eibach-pro-kit-performance-lowering-springs-clean.jpg?v=1791831021"}],"url":"https:\/\/suspengo.com\/collections\/suspension-renault-scenic\/series-b4.oembed","provider":"Suspengo","version":"1.0","type":"link"}