Eibach Pro-Street-S Coilover Kit PSS65-46-025-01-22 – Hyundai i30 / Kia PRO-CEE D-2

Eibach Pro-Street-S coilover kit PSS65-46-025-01-22 for the Hyundai i30 (GD), a 30–55 mm at the front and 20–50 mm at the rear change in ride height, approved to 1050 kg front and 1050 kg rear axle load, covering 3 vehicle variants in the Eibach application list.

Specifications

• Manufacturer: Eibach
• Product line: Pro-Street-S
• Part number: PSS65-46-025-01-22
• Lowering, front: 30–55 mm, depending on engine
• Lowering, rear: 20–50 mm, depending on engine
• 1.4, 1.6, 1.6 GDI, 1.4 CRDi, 1.6 CRDi, 1.6 T-GDi, 1.8, 2.0: 30–50 mm front / 20–45 mm rear
• 1.0 T-GDI, 1.4 MPI, 1.4 CVVT, 1.6 CVVT, 1.6 GDI, 1.4 CRDi 90, 1.6 CRDi 110, 1.6 CRDi 11…: 35–55 mm front / 25–50mm rear
• Permitted axle load, front: 1050 kg
• Permitted axle load, rear: 1050 kg
• Spring part numbers: F67-46-025-01-FA, F67-46-025-01-RA
• Damper part numbers: 1 × front damper, left PSS66-46-025-01-FL, 1 × front damper, right PSS66-46-025-01-FR, 2 × rear damper PSS66-46-025-01-RA
• Type-approval marking: T
• Certificate document: E654602501.pdf
• Fitting instructions: M654602501.pdf, Entsorgungsanleitung.pdf
• Applications covered: 3 vehicles, 3 fitment rows

Performance

Pro-Street-S is a height-adjustable coilover set: ride height is set anywhere across 30–55 mm at the front and 20–50 mm at the rear by moving the spring seat on the strut body, so the stance can be tuned to the wheel and tyre actually fitted. Damping is fixed and factory-valved for the spring rates supplied, which keeps setup simple — set the height, check the geometry, drive.

Fitment

Fits Hyundai i30 (GD), from 11/2011, FWD; Kia Cee'd (JD), 05/2012–07/2018; and Kia PRO Cee'd (JD), from 03/2013, FWD — see the full list below. Verify fitment using the vehicle compatibility checker above.

The full Eibach range and what each line is for is set out on our Eibach ranges page.

What's Included

One complete Eibach Pro-Street-S coilover set for this vehicle — adjustable strut assemblies and their matched springs for both axles, supplied together. Struts: 1 × front damper, left PSS66-46-025-01-FL · 1 × front damper, right PSS66-46-025-01-FR · 2 × rear damper PSS66-46-025-01-RA. Springs: F67-46-025-01-FA · F67-46-025-01-RA. Top mounts, bump stops and fixings are re-used from the vehicle unless the specification table above lists them.

Warranty

Backed by Eibach's manufacturer warranty against defects in materials and workmanship. Cover assumes the set is fitted complete and as supplied, by a workshop with the correct spring tooling. Mixing these parts with springs or dampers from another set puts the load outside what this set was tuned for and is not covered. As an official reseller in the EU, Suspengo also handles your statutory conformity rights on this purchase — contact us first and we deal with the manufacturer.

Notes

• If not separately named, for vehicles with OE-lowered suspension, the dimension of lowering is reduced by the dimension of lowering carried out by manufacturer. If not separately named, vehicles with OE-lifted suspension (e.g. Offroad-Package, Crossover) are excluded from use of our products.
• The specifications indicated in the Components Certificate are for the classification of the item / vehicle. Please check the type Components Certificate number of your car and compare with the Components Certificate. (Letter "K" in your vehicle registration certificate or to find at the type plate of your car!)
• Please verify before fitting by means of the Components Certificate whether the delivered items (please see marking) are approved for your vehicle (please see area of use).You can find the current Components Certificate on www.eibach.de
• In case of non-conformance the items must not be fitted – please refer to your dealer.
• Mounting - we recommend to have our spring system installed by a qualified workshop only, that has skilled personnel and the required special tools available. - If the installation deviates from the workshop manual, Eibach-Eibach instructions are available online.
• Mounting position - you can "read" the mounting position of the springs from the imprint - have them installed just the way you read the imprint.
• Wheel adjustment - after completion of the spring/suspension installation, checking the wheel adjustment is required.
• Shock absorbers - if the standard shock absorbers are not fully operative anymore and their efficiency has worn off considerably, we strongly recommend to replace those by new standard shock absorbers or by sports shock absorbers, if using lowering springs. This already can be necessary from 40.000 kilometers OE-damper-milage.
• The installation of Sport-Shock Absobers is recommended with Sportline springs. As example Bilstein B8
• Here all wheel/tyre-combinations are possible, which are released by the wheel type testing institution. The instructions in the wheel Components Certificate have to be adhered to, except for: OE suspension is required.
• Depending on engine, gearbox/transmission, equipment and vehicle tolerances lowering may differ from the values given. The dimension of lowering is reduced by the dimension of lowering carried out by manufacturer.
• The applicability of our products deals with standard cars. In any case of reconstruction (even with OE-accessory-parts), as the installation of an accessory-brake-system (e.g. ceramic-brakes), sport-suspension, LPG-(liquefied petroleum gas)-system for example, the usage of our products may be excluded. The stated measurements are referring to new standard cars. Measuring points: vertical distance from the middle of the wheel hub to the bottom edge of the mud wing. Generally the stated measurements are nominal values, which can vary depending on every car.
• If your vehicle has serial electronic damper control this will not be available anymore while using the B12- or Pro-Street-S-suspension kit. You will see a trouble code. This can be re-programed by an official garage/dealership. If available for your vehicle, we recommend to use Pro-Tronic to avoid the trouble code.
• Front axle height adjustable by threaded strut, rear axle by height adjustable unit.
• In order to ensure sufficient clearance it may be necessary to use wheel spacers if the car is equipped with original wheel sizes.
• In some cases additional OE-Parts for the installation of the suspension componends are required. Therefore please take a look at the corresponding technical documents which are available on our website.
• If replacement required: You will find the components in the Components Certificate at the point "Amendment of the vehicle documents". The Components Certificate can be downloaded on: www.eibach.com - click on British flag - Online Catalog / Product & Components Certificate Search (RED BUTTON)